參數資料
型號： EPC16QC100N
廠商： Altera
文件頁數： 16/36頁
文件大小： 0K
描述： IC CONFIG DEVICE 16MBIT 100-PQFP
產品培訓模塊： Three Reasons to Use FPGA's in Industrial Designs
標準包裝： 66
系列： EPC
可編程類型： 系統內可編程
存儲容量： 16Mb
電源電壓： 3 V ~ 3.6 V
工作溫度： 0°C ~ 70°C
封裝/外殼： 100-BQFP
供應商設備封裝： 100-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 604 (CN2011-ZH PDF)
其它名稱： 544-1681
Pin Description
Page 23
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
Table 9. External Flash Interface Pins (Part 1 of 2)
Pin Name
Pin Type
Description
A[20..0]
Input
These pins are the address input to the flash memory for read and write
operations. The addresses are internally latched during a write cycle.
When the external flash interface is not used, leave these pins floating (with a few
exceptions (1)). These flash address, data, and control pins are internally
connected to the configuration controller.
In the 100-pin PQFP package, four address pins (A0, A1, A15, A16) are not
internally connected to the controller. These loop-back connections must be made
on the board between the C-A[] and F-A[] pins even when you are not using the
external flash interface. All other address pins are connected internal to the
package.
All address pins are connected internally in the 88-pin UFBGA package.
Pin A20 in EPC16 devices, pins A20 and A19 in EPC8 devices, and pins A20, A19,
and A18 in EPC4 devices are NC pins. These pins should be left floating on the
board.
DQ[15..0]
Bidirectional
This is the flash data bus interface between the flash memory and the controller.
The controller or an external source drives DQ[15..0] during the flash command
and the data write bus cycles. During the data read cycle, the flash memory drives
the DQ[15..0] to the controller or external device.
Leave these pins floating on the board when the external flash interface is not
used.
CE#
Input
Active low flash input pin that activates the flash memory when asserted. When it
is high, it deselects the device and reduces power consumption to standby levels.
This flash input pin is internally connected to the controller.
Leave this pin floating on the board when the external flash interface is not used.
RP# (1)
Input
Active low flash input pin that resets the flash when asserted. When high, it
enables normal operation. When low, it inhibits write operation to the flash
memory, which provides data protection during power transitions.
This flash input is not internally connected to the controller. Hence, an external
loop-back connection between C-RP# and F-RP# must be made on the board
even when you are not using the external flash interface.
When using the external flash interface, connect the external device to the RP# pin
with the loop back. Always tri-state RP# when the flash is not in use.
OE#
Input
Active-low flash-control input that is asserted by the controller or external device
during flash read cycles. When asserted, it enables the drivers of the flash output
pins.
Leave this pin floating on the board when the external flash interface is not used.
WE# (1)
Input
Active-low flash-write strobe asserted by the controller or external device during
flash write cycles. When asserted, it controls writes to the flash memory. In the
flash memory, addresses and data are latched on the rising edge of the WE# pulse.
This flash input is not internally connected to the controller. Hence, an external
loop-back connection between C-WE# and F-WE# must be made on the board
even when you are not using the external flash interface.
When using the external flash interface, connect the external device to the WE# pin
with the loop back.
相關PDF資料
PDF描述
NCV8506D2T33R4G IC REG LDO 3.3V .4A D2PAK-7
RBB06DHND CONN EDGECARD 12POS DIP .050 SLD
LTC4303CDD#PBF IC BUS BUFFER I2C 8-DFN
NCV8518PDG IC REG LDO 5V .25A 8SOIC-EP
TCJC156M035R0200 CAP TANT 15UF 35V 20% 2312
相關代理商/技術參數
參數描述
EPC16QI100 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC16QI100N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC16UC88 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
EPC16UC88AA 功能描述:IC CONFIG DEVICE 16MBIT 88-UBGA RoHS:否 類別:集成電路 (IC) >> 存儲器 - 用于 FPGA 的配置 Proms 系列:EPC 產品變化通告:Product Discontinuation 28/Jul/2010 標準包裝:98 系列:- 可編程類型:OTP 存儲容量:300kb 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-TSOP 包裝:管件
EPC16UC88N 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*