參數資料
型號: EPM7128AETC100-10N
廠商: Altera
文件頁數: 17/64頁
文件大小: 0K
描述: IC MAX 7000 CPLD 128 100-TQFP
產品變化通告: Bond Wire Change 4/Sept/2008
標準包裝: 270
系列: MAX® 7000A
可編程類型: 系統內可編程
最大延遲時間 tpd(1): 10.0ns
電壓電源 - 內部: 3 V ~ 3.6 V
邏輯元件/邏輯塊數目: 8
宏單元數: 128
門數: 2500
輸入/輸出數: 84
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 100-TQFP
供應商設備封裝: 100-TQFP(14x14)
包裝: 托盤
產品目錄頁面: 604 (CN2011-ZH PDF)
其它名稱: 544-2027
EPM7128AETC100-10N-ND
24
Altera Corporation
MAX 7000A Programmable Logic Device Data Sheet
Programmable
Speed/Power
Control
MAX 7000A devices offer a power-saving mode that supports low-power
operation across user-defined signal paths or the entire device. This
feature allows total power dissipation to be reduced by 50% or more
because most logic applications require only a small fraction of all gates to
operate at maximum frequency.
The designer can program each individual macrocell in a MAX 7000A
device for either high-speed (i.e., with the Turbo BitTM option turned on)
or low-power operation (i.e., with the Turbo Bit option turned off). As a
result, speed-critical paths in the design can run at high speed, while the
remaining paths can operate at reduced power. Macrocells that run at low
power incur a nominal timing delay adder (tLPA) for the tLAD, tLAC, tIC,
tEN, tSEXP, tACL, and tCPPW parameters.
Output
Configuration
MAX 7000A device outputs can be programmed to meet a variety of
system-level requirements.
MultiVolt I/O Interface
The MAX 7000A device architecture supports the MultiVolt I/O interface
feature, which allows MAX 7000A devices to connect to systems with
differing supply voltages. MAX 7000A devices in all packages can be set
for 2.5-V, 3.3-V, or 5.0-V I/O pin operation. These devices have one set of
VCC
pins for internal operation and input buffers (VCCINT), and another
set for I/O output drivers (VCCIO).
The VCCIO pins can be connected to either a 3.3-V or 2.5-V power supply,
depending on the output requirements. When the VCCIO pins are
connected to a 2.5-V power supply, the output levels are compatible with
2.5-V systems. When the VCCIO pins are connected to a 3.3-V power
supply, the output high is at 3.3 V and is therefore compatible with 3.3-V
or 5.0-V systems. Devices operating with VCCIO levels lower than 3.0 V
incur a slightly greater timing delay of tOD2 instead of tOD1. Inputs can
always be driven by 2.5-V, 3.3-V, or 5.0-V signals.
Table 12 describes the MAX 7000A MultiVolt I/O support.
Table 12. MAX 7000A MultiVolt I/O Support
VCCIO Voltage
Input Signal (V)
Output Signal (V)
2.5
3.3
5.0
2.5
3.3
5.0
2.5
vvvv
3.3
vvv
vv
相關PDF資料
PDF描述
EPM7128AETC100-10 IC MAX 7000 CPLD 128 100-TQFP
EPM7128STC100-15 IC MAX 7000 CPLD 128 100-TQFP
EPM7128STC100-15N IC MAX 7000 CPLD 128 100-TQFP
RCB108DHFD CONN EDGECARD 216POS .050 SMD
GCM2165C2A222JA16D CAP CER 2200PF 100V 5% NP0 0805
相關代理商/技術參數
參數描述
EPM7128AETC100-5 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM7128AETC100-5N 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM7128AETC100-7 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM7128AETC1007N 制造商:Altera Corporation 功能描述:
EPM7128AETC100-7N 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池?cái)?shù)量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100