Choose the new required VOUTMAX and VOUT" />
參數資料
型號： EVAL-AD5361EBZ
廠商： Analog Devices Inc
文件頁數： 11/29頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD5361
產品培訓模塊： DAC Architectures
標準包裝： 1
DAC 的數量： 16
位數： 14
采樣率（每秒）： 540k
數據接口： 串行
設置時間： 20µs
DAC 型： 電壓
工作溫度： -40°C ~ 85°C
已供物品： 板，CD
已用 IC / 零件： AD5361
相關產品： AD5361BSTZ-REEL-ND - IC DAC 14BIT 16CH SERIAL 52-LQFP
AD5361BSTZ-ND - IC DAC 14BIT 16CH SERIAL 56LQFP
AD5361BCPZ-REEL7-ND - IC DAC 14BIT 16CH SERIAL 56LFCSP
AD5361BCPZ-ND - IC DAC 14BIT 16CH SERIAL 56LFCSP
AD5360/AD5361
Rev. A | Page 18 of 28
4.
Choose the new required VOUTMAX and VOUTMIN, keeping
the VOUT limits centered on the nominal values. Note that
VDD and VSS must provide sufficient headroom.
5.
Calculate the value of VREF as follows:
VREF = (VOUTMAX VOUTMIN)/4
Reference Selection Example
Nominal output range = 20 V (10 V to +10 V)
Offset error = ±100 mV
Gain error = ±3%
SIGGND = AGND = 0 V
Gain error = ±3%
Maximum positive gain error = +3%
Output range including gain error = 20 + 0.03 (20) =
20.6 V
Offset error = ±100 mV
Maximum offset error span = 2 (100 mV) = 0.2 V
Output range including gain error and offset error =
20.6 V + 0.2 V = 20.8 V
VREF calculation
Actual output range = 20.6 V, that is, 10.3 V to +10.3 V
(centered);
VREF = (10.3 V + 10.3 V)/4 = 5.15 V
If the solution yields an inconvenient reference level, the user
can adopt one of the following approaches:
Use a resistor divider to divide down a convenient, higher
reference level to the required level.
Select a convenient reference level above VREF and modify
the gain and offset registers to digitally downsize the
reference. In this way, the user can use almost any conven-
ient reference level but may reduce the performance by
overcompaction of the transfer function.
Use a combination of these two approaches.
CALIBRATION
The user can perform a system calibration on the AD5360 and
AD5361 to reduce gain and offset errors to below 1 LSB. This is
achieved by calculating new values for the M and C registers and
reprogramming them.
Reducing Zero-Scale and Full-Scale Error
Zero-scale error can be reduced as follows:
1.
Set the output to the lowest possible value.
2.
Measure the actual output voltage and compare it with the
required value. This gives the zero-scale error.
3.
Calculate the number of LSBs equivalent to the error and
add this from the default value of the C register. Note that
only negative zero-scale error can be reduced.
Full-scale error can be reduced as follows:
1.
Measure the zero-scale error.
2.
Set the output to the highest possible value.
3.
Measure the actual output voltage and compare it with the
required value. Add this error to the zero-scale error. This
is the span error, which includes full-scale error.
4.
Calculate the number of LSBs equivalent to the span error
and subtract it from the default value of the M register.
Note that only positive full-scale error can be reduced.
The M and C registers should not be programmed until both
zero-scale errors and full-scale errors have been calculated.
AD5360 Calibration Example
This example assumes that a 10 V to +10 V output is required.
The DAC output is set to 10 V but is measured at 10.03 V.
This gives a zero-scale error of 30 mV.
1 LSB = 20 V/65,536 = 305.176 μV
30 mV = 98 LSBs
The full-scale error can now be removed. The output is set
to +10 V, and a value of +10.02 V is measured. The full-scale
error is +20 mV. The span error is +20 mV (30 mV) =
+50 mV.
+50 mV = 164 LSBs
The errors can now be removed.
1.
98 LSBs should be added to the default C register value;
(32,768 + 98) = 32,866.
2.
32,866 should be programmed to the C register.
3.
164 LSBs should be subtracted from the default M register
value; (65,535 164) = 65,371.
4.
65,371 should be programmed to the M register.
Additional Calibration
The techniques described in the previous section are usually
enough to reduce the zero-scale errors and full-scale errors in
most applications. However, there are limitations whereby the
errors may not be sufficiently removed. For example, the offset
(C) register can only be used to reduce the offset caused by the
negative zero-scale error. A positive offset cannot be reduced.
Likewise, if the maximum voltage is below the ideal value, that
is, a negative full-scale error, the gain (M) register cannot be
used to increase the gain to compensate for the error.
These limitations can be overcome by increasing the refer-
ence value. With a 2.5 V reference, a 10 V span is achieved.
The ideal voltage range, for the AD5360 or AD5361, is
5 V to +5 V. Using a 2.6 V reference increases the range
to 5.2 V to +5.2 V. Clearly, in this case, the offset and gain
errors are insignificant and the M and C registers can be
used to raise the negative voltage to 5 V and then reduce
the maximum voltage down to +5 V to give the most
accurate values possible.
相關PDF資料
PDF描述
V300C2E50BF3 CONVERTER MOD DC/DC 2V 50W
0210490910 CABLE JUMPER 1.25MM .178M 21POS
V24C5E125BL2 CONVERTER MOD DC/DC 5V 125W
EVAL-AD5433EBZ BOARD EVAL FOR AD5433
HCC08DRES-S13 CONN EDGECARD 16POS .100 EXTEND
相關代理商/技術參數
參數描述
EVAL-AD5361EBZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Channel, 16-/14-Bit, Serial Input, Voltage-Output DAC
EVAL-AD5362EBZ 功能描述:BOARD EVAL FOR AD5362 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5363EBZ 功能描述:BOARD EVALUATION FOR AD5363 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5370EBZ 功能描述:BOARD EVALUATION FOR AD5370 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
EVAL-AD5371EBZ 功能描述:BOARD EVAL FOR AD5371 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*