- 您現在的位置：買賣IC網 > PDF目錄17103 > EVAL-AD5791SDZ (Analog Devices Inc)BOARD EVAL FOR AD5791 PDF資料下載
參數資料
| 型號： | EVAL-AD5791SDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 18/29頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD5791 |
| 標準包裝： | 1 |
| DAC 的數量： | 1 |
| 位數： | 20 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 設置時間： | 1µs |
| DAC 型： | 電壓 |
| 工作溫度： | -40°C ~ 125°C |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | AD5791 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
AD5791
Data Sheet
Rev. D | Page 24 of 28
AD5791 FEATURES
POWER-ON TO 0 V
The AD5791 contains a power-on reset circuit that, as well as
resetting all registers to their default values, controls the output
voltage during power-up. Upon power-on the DAC is placed in
tristate (its reference inputs are disconnected) and its output is
clamped to ground through a ~6 kΩ resistor. The DAC remains
in this state until programmed otherwise via the control
register. This is a useful feature in applications where it is
important to know the state of the DAC output while it is in the
process of powering up.
CONFIGURING THE AD5791
After power-on the AD5791 must be configured to put it into
normal operating mode before programming the output. To do
this, the control register must be programmed. The DAC is
removed from tristate by clearing the DACTRI bit, and the
output clamp is removed by clearing the OPGND bit. At this
point, the output goes to VREFN, unless an alternative value is
first programmed to the DAC register.
DAC OUTPUT STATE
The DAC output can be placed in one of three states, controlled
by the DACTRI and OPGND bits of the control register, as
shown in Table 16.
Table 16. AD5791 Output State Truth Table
DACTRI
OPGND
Output State
0
Normal operating mode
0
1
Output is clamped via ~6 kΩ to AGND
1
0
Output is in tristate
1
Output is clamped via ~6 kΩ to AGND
LINEARITY COMPENSATION
The integral nonlinearity (INL) of the AD5791 can vary according
to the applied reference voltage span, the LIN COMP bits of
the control register can be programmed to compensate for
this variation in INL. The specifications in this data sheet are
obtained with LIN COMP = 0000 for reference spans up to
and including 10 V and with LIN COMP = 1100 for a reference
span of 20 V. The default value of the LIN COMP bits is 0000.
Intermediate LIN COMP values can be programmed for reference
spans between 10 V and 20 V as shown in Table 12.
OUTPUT AMPLIFIER CONFIGURATION
There are a number of different ways that an output amplifier
can be connected to the AD5791, depending on the voltage
references applied and the desired output voltage span.
Unity Gain Configuration
Figure 50 shows an output amplifier configured for unity gain,
in this configuration the output spans from VREFN to VREFP.
A1
6.8k 6.8k
R1
RFB
20-BIT
DAC
VREFPS
VREFPF
VREFP
VREFN
VREFNS
AD5791
1/2 AD8676
AD8675,
ADA4898-1
1/2 AD8676
VREFNF
RFB
INV
VOUT
0
89
64-
051
Figure 50. Output Amplifier in Unity Gain Configuration
A second unity gain configuration for the output amplifier is
one that removes an offset from the input bias currents of the
amplifier. It does this by inserting a resistance in the feedback
path of the amplifier that is equal to the output resistance of the
DAC. The DAC output resistance is 3.4 kΩ, by connecting R1
and RFB in parallel, a resistance equal to the DAC resistance is
available on chip. Because the resistors are all on one piece of
silicon, they are temperature coefficient matched. To enable this
mode of operation the RBUF bit of the control register must be
set to Logic 1. Figure 51 shows how the output amplifier is
connected to the AD5791. In this configuration, the output
amplifier is in unity gain and the output spans from VREFN to
VREFP. This unity gain configuration allows a capacitor to be placed
in the amplifier feedback path to improve dynamic performance.
20-BIT
DAC
VREFPS
10pF
VREFPF
VREFP
VREFN
VREFNS
AD5791
1/2 AD8676
AD8675,
ADA4898-1
1/2 AD8676
VREFNF
VOUT
RFB
VOUT
08
96
4-
05
2
INV
6.8k
R1
Figure 51. Output Amplifier in Unity Gain with Amplifier Input Bias Current
Compensation
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J2R-EZ | CONVERTER MOD DC/DC 7.5V 25W |
| VE-J2N-EZ | CONVERTER MOD DC/DC 18.5V 25W |
| VE-J21-EZ | CONVERTER MOD DC/DC 12V 25W |
| VI-JWZ-EZ | CONVERTER MOD DC/DC 2V 10W |
| VI-JWV-EZ | CONVERTER MOD DC/DC 5.8V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5821AEBZ | 功能描述:BOARD EVAL FOR AD5821 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5821EBZ | 功能描述:BOARD EVALUATION FOR AD5821 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5821EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:120 mA, Current Sinking, 10-Bit, I2C DAC |
| EVAL-AD5930EB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD I.C. - Bulk |
| EVAL-AD5930EBZ | 功能描述:BOARD EVAL FOR AD5930 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。