- 您現在的位置：買賣IC網 > PDF目錄17058 > EVAL-AD7298SDZ (Analog Devices Inc)BOARD EVAL FOR AD7298 PDF資料下載
參數資料
| 型號： | EVAL-AD7298SDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/25頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD7298 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，串行，SPI? |
| 工作溫度： | -40°C ~ 125°C |
| 已用 IC / 零件： | AD7298 |
| 已供物品： | 板，纜線，CD |
AD7298
Rev. B | Page 7 of 24
PIN CONFIGURATION AND FUNCTION DESCRIPTION
14
13
12
1
3
4
DOUT
15
SCLK
DIN
TSENSE_BUSY
11
CS
VIN3
VIN5
2
VIN4
VIN6
5
VIN7
7
V
R
E
F
6
G
N
D
1
8
D
C
A
P
9
G
N
D
10
V
D
19
V
IN
1
20
V
IN
2
18
V
IN
0
17
P
D
/R
S
T
16
V
D
R
IV
E
AD7298
TOP VIEW
(Not to Scale)
08
75
4-
00
3
NOTES
1. THE EXPOSED METAL PADDLE ON THE BOTTOM
OF THE LFCSP PACKAGE SHOULD BE SOLDERED
TO PCB GROUND FOR PROPER FUNCTIONALITY
AND HEAT DISSIPATION.
Figure 2. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1 to 5,
18 to 20
VIN3, VIN4,
VIN5, VIN6,
VIN7, VIN0,
VIN1, VIN2
Analog Inputs. The AD7298 has eight single-ended analog inputs that are multiplexed into the on-chip track-
and-hold. Each input channel can accept analog inputs from 0 V to 2.5 V. Any unused input channels should be
connected to GND1 to avoid noise pickup.
6
GND1
Ground. Ground reference point for the internal reference circuitry on the AD7298. The external reference signals
and all analog input signals should be referred to this GND1 voltage. The GND1 pin should be connected to the
GND plane of a system. All ground pins should ideally be at the same potential and must not be more than 0.3 V
apart, even on a transient basis. The VREF pin should be decoupled to this ground pin via a 10 μF decoupling
capacitor.
7
VREF
Internal Reference/External Reference Supply. The nominal internal reference voltage of 2.5 V appears at this pin.
Provided the output is buffered, the on-chip reference can be taken from this pin and applied externally to the
rest of a system. Decoupling capacitors should be connected to this pin to decouple the reference buffer. For
best performance, it is recommended to use a 10 μF decoupling capacitor on this pin to GND1. The internal
reference can be disabled and an external reference supplied to this pin, if required. The input voltage range for
the external reference is 2.0 V to 2.5 V.
8
DCAP
Decoupling Capacitor Pin. Decoupling capacitors (1 μF recommended) are connected to this pin to decouple the
internal LDO.
9
GND
Ground. Ground reference point for all analog and digital circuitry on the AD7298. The GND pin should be
connected to the ground plane of the system. All ground pins should ideally be at the same potential and must
not be more than 0.3 V apart, even on a transient basis. Both DCAP and VDD pins should be decoupled to this
GND pin.
10
VDD
Supply Voltage, 2.8 V to 3.6 V. This supply should be decoupled to GND with 10 μF and 100 nF decoupling
capacitors.
11
CS
Chip Select, Active Low Logic Input. This pin is edge triggered on the falling edge of this input, the track-and-
hold goes into hold mode, and a conversion is initiated. This input also frames the serial data transfer. When CS is
low, the output bus is enabled, and the conversion result becomes available on the DOUT output.
12
TSENSE_BUSY
Busy Output. This pin transitions high when a temperature sensor conversion starts and remains high until the
conversion completes.
13
DIN
Data In, Logic input. Data to be written to the AD7298 control register is provided on this input and is clocked
into the register on the falling edge of SCLK.
14
DOUT
Serial Data Output. The conversion result from the AD7298 is provided on this output as a serial data stream. The
bits are clocked out on the falling edge of the SCLK input. The data stream from the AD7298 consists of four
address bits indicating which channel the conversion result corresponds to, followed by the 12 bits of conversion
data (MSB first). The output coding is straight binary for the voltage channels and twos complement for the
temperature sensor result.
15
SCLK
Serial Clock, Logic Input. A serial clock input provides the SCLK for accessing the data from the AD7298.
相關PDF資料 |
PDF描述 |
|---|---|
| RPP20-243.3S/N | CONV DC/DC 20W 18-36VIN 3.3VOUT |
| RPP20-2424D/N | CONV DC/DC 20W 18-36VIN +/-24V |
| EEM30DRMD | CONN EDGECARD 60POS .156 WW |
| RPP20-2415S/N | CONV DC/DC 20W 18-36VIN 15VOUT |
| CDB4364 | EVALUATION BOARD FOR CS4364 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7298SDZ | 制造商:Analog Devices 功能描述:EVAL BOARD, AD7192 12BIT ADC |
| EVAL-AD7321CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:500 kSPS, 2-Channel, Software-Selectable, True Bipolar Input, 12-Bit Plus Sign ADC |
| EVAL-AD7321CBZ | 功能描述:BOARD EVALUATION FOR AD7321 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7322CB1 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Software Selectable True Bipolar Input, 2-Channel, 12-Bit Plus Sign ADC |
| EVAL-AD7322CBZ | 功能描述:BOARD EVALUATION FOR AD7322 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。