- 您現在的位置：買賣IC網 > PDF目錄17038 > EVAL-AD7610CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7610 PDF資料下載
參數資料
| 型號： | EVAL-AD7610CBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7610 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行，并聯 |
| 在以下條件下的電源（標準）： | 90mW @ 250kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7610 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7610
Data Sheet
Rev. A | Page 30 of 32
APPLICATION INFORMATION
LAYOUT GUIDELINES
While the AD7610 has very good immunity to noise on the
power supplies, exercise care with the grounding layout. To facil-
itate the use of ground planes that can be easily separated, design
the printed circuit board that houses the AD7610 so that the
analog and digital sections are separated and confined to certain
areas of the board. Digital and analog ground planes should be
joined in only one place, preferably underneath the AD7610, or
as close as possible to the AD7610. If the AD7610 is in a system
where multiple devices require analog-to-digital ground connect-
ions, the connections should still be made at one point only, a
star ground point, established as close as possible to the AD7610.
To prevent coupling noise onto the die, avoid radiating noise,
and to reduce feedthrough:
Do not run digital lines under the device.
Do run the analog ground plane under the AD7610.
Do shield fast switching signals, like CNVST or clocks, with
digital ground to avoid radiating noise to other sections of
the board, and never run them near analog signal paths.
Avoid crossover of digital and analog signals.
Run traces on different but close layers of the board, at right
angles to each other, to reduce the effect of feedthrough through
the board.
The power supply lines to the AD7610 should use as large a trace as
possible to provide low impedance paths and reduce the effect of
glitches on the power supply lines. Good decoupling is also
important to lower the impedance of the supplies presented to
the AD7610, and to reduce the magnitude of the supply spikes.
Decoupled ceramic capacitors, typically 100 nF, should be placed
on each of the power supplies pins, AVDD, DVDD, and OVDD,
VCC, and VEE. The capacitors should be placed close to, and
ideally right up against, these pins and their corresponding ground
pins. Additionally, low ESR 10 F capacitors should be located
in the vicinity of the ADC to further reduce low frequency ripple.
The DVDD supply of the AD7610 can be either a separate supply
or come from the analog supply, AVDD, or from the digital
interface supply, OVDD. When the system digital supply is noisy,
or fast switching digital signals are present, and no separate supply
is available, it is recommended to connect the DVDD digital supply
to the analog supply AVDD through an RC filter, and to connect
the system supply to the interface digital supply OVDD and the
remaining digital circuitry. See Figure 27 for an example of this
configuration. When DVDD is powered from the system supply,
it is useful to insert a bead to further reduce high frequency spikes.
The AD7610 has four different ground pins: REFGND, AGND,
DGND, and OGND.
REFGND senses the reference voltage and, because it carries
pulsed currents, should be a low impedance return to the
reference.
AGND is the ground to which most internal ADC analog
signals are referenced; it must be connected with the least
resistance to the analog ground plane.
DGND must be tied to the analog or digital ground plane
depending on the configuration.
OGND is connected to the digital system ground.
The layout of the decoupling of the reference voltage is important.
To minimize parasitic inductances, place the decoupling capacitor
close to the ADC and connect it with short, thick traces.
EVALUATING PERFORMANCE
A recommended layout for the AD7610 is outlined in the EVAL-
AD7610EDZ evaluation board documentation. The evaluation
board package includes a fully assembled and tested evaluation
board, documentation, and software for controlling the board
from a PC via the EVAL-CED1Z.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7651CBZ | BOARD EVALUATION FOR AD7651 |
| EVAL-AD7694CBZ | BOARD EVALUATION FOR AD7694 |
| 0210490994 | CABLE JUMPER 1.25MM .127M 29POS |
| RBC08DREH-S93 | CONN EDGECARD 16POS .100 EYELET |
| EVAL-AD7684CBZ | BOARD EVALUATION FOR AD7684 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7610EDZ | 功能描述:BOARD EVAL FOR AD7610 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7612CB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD7612 - Bulk |
| EVAL-AD7612CBZ | 功能描述:BOARD EVALUATION FOR AD7612 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7612EDZ | 功能描述:BOARD EVAL FOR AD7612 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7621CB2 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 2 LSB INL, 3 MSPS PulSAR?? ADC |
發布緊急采購，3分鐘左右您將得到回復。