- 您現在的位置：買賣IC網 > PDF目錄17036 > EVAL-AD7689EDZ (Analog Devices Inc)BOARD EVAL AD7689 PDF資料下載
參數資料
| 型號： | EVAL-AD7689EDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL AD7689 |
| 產品培訓模塊： | Motor Control |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 12.5mW @ 250kSPS，5V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7689 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7682/AD7689
Rev. D | Page 19 of 32
Unipolar or Bipolar
Figure 26 shows an example of the recommended connection
available.
Bipolar Single Supply
Figure 27 shows an example of a system with a bipolar input
using single supplies with the internal reference (optional
different VIO supply). This circuit is also useful when the
amplifier/signal conditioning circuit is remotely located with
some common mode present. Note that for any input config-
uration, the INx inputs are unipolar and are always referenced
to GND (no negative voltages even in bipolar range).
For this circuit, a rail-to-rail input/output amplifier can be used;
however, the offset voltage vs. input common-mode range should
be noted and taken into consideration (1 LSB = 62.5 μV with
VREF = 4.096 V). Note that the conversion results are in twos
complement format when using the bipolar input configuration.
Refer to the AN-581 Application Note, Biasing and Decoupling
Op Amps in Single Supply Applications, for additional details
about using single-supply amplifiers.
ANALOG INPUTS
Input Structure
Figure 28 shows an equivalent circuit of the input structure of
protection for the analog inputs, IN[7:0] and COM. Care must
be taken to ensure that the analog input signal does not exceed
the supply rails by more than 0.3 V because this causes the
diodes to become forward biased and to start conducting
current.
These diodes can handle a forward-biased current of 130 mA
maximum. For instance, these conditions may eventually occur
when the input buffer supplies are different from VDD. In such
a case, for example, an input buffer with a short circuit, the
current limitation can be used to protect the part.
CIN
RIN
D1
D2
CPIN
INx+
OR INx–
OR COM
GND
VDD
07
35
3-
0
3
0
Figure 28. Equivalent Analog Input Circuit
This analog input structure allows the sampling of the true
differential signal between INx+ and COM or INx+ and INx.
(COM or INx = GND ± 0.1 V or VREF ± 0.1 V). By using these
differential inputs, signals common to both inputs are rejected,
as shown in Figure 29.
70
65
60
55
50
45
40
35
30
1
10k
10
CM
RR
(
d
B)
100
1k
FREQUENCY (kHz)
07
35
3-
03
1
Figure 29. Analog Input CMRR vs. Frequency
During the acquisition phase, the impedance of the analog inputs
can be modeled as a parallel combination of the capacitor, CPIN,
and the network formed by the series connection of RIN and CIN.
CPIN is primarily the pin capacitance. RIN is typically 2.2 kΩ and
is a lumped component composed of serial resistors and the on
resistance of the switches. CIN is typically 27 pF and is mainly
the ADC sampling capacitor.
Selectable Low-Pass Filter
During the conversion phase, where the switches are opened,
filter that reduces undesirable aliasing effects and limits the
noise from the driving circuitry. The low-pass filter can be pro-
grammed for the full bandwidth or of the bandwidth with
Note that the converter throughput must also be reduced by
when using the filter. If the maximum throughput is used with the
bandwidth (BW) set to , the converter acquisition time, tACQ, is
violated, resulting in increased THD.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J1J-EY | CONVERTER MOD DC/DC 36V 50W |
| EVAL-AD7682EDZ | BOARD EVAL AD7682 |
| LGU2E331MELZ | CAP ALUM 330UF 250V 20% SNAP |
| EVAL-AD7982SDZ | BOARD EVAL FOR AD7982 |
| VI-J1L-EY | CONVERTER MOD DC/DC 28V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7689EDZ | 制造商:Analog Devices 功能描述:16 Bit A/D Converter Eval. Board |
| EVAL-AD7690CB | 制造商:Analog Devices 功能描述:AD7690 EVAL - Bulk |
| EVAL-AD7690SDZ | 功能描述:BOARD EVAL FOR AD7690 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7691CBZ | 功能描述:BOARD EVALUATION FOR AD7691CBZ RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7691SDZ | 功能描述:BOARD EVAL FOR AD7691 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。