- 您現在的位置：買賣IC網 > PDF目錄17058 > EVAL-AD7985EBZ (Analog Devices Inc)BOARD EVAL FOR AD7985 PDF資料下載
參數資料
| 型號： | EVAL-AD7985EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 9/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7985 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 2.5M |
| 數據接口： | SPI?、QSPI?、MICROWIRE? 和 DSP |
| 輸入范圍： | 0 ~ 5 V |
| 在以下條件下的電源（標準）： | 15.5mW @ 2.5MSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7985 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
AD7985
Rev. A | Page 17 of 28
DIGITAL INTERFACE
Although the AD7985 has a reduced number of pins, it offers
flexibility in its serial interface modes.
In CS mode, the AD7985 is compatible with SPI, MICROWIRE,
QSPI, and digital hosts. In CS mode, the AD7985 can use either
a 3-wire or a 4-wire interface. A 3-wire interface that uses the
CNV, SCK, and SDO signals minimizes wiring connections,
which is useful, for example, in isolated applications. A 4-wire
interface that uses the SDI, CNV, SCK, and SDO signals allows
CNV, which initiates conversions, to be independent of the
readback timing (SDI). This is useful in low jitter sampling
or simultaneous sampling applications.
In chain mode, the AD7985 provides a daisy-chain feature that
uses the SDI input for cascading multiple ADCs on a single data
line similar to a shift register. Chain mode is available only in
normal mode (TURBO is low).
The mode in which the part operates depends on the SDI level
when the CNV rising edge occurs. CS mode is selected if SDI
is high, and chain mode is selected if SDI is low. The SDI hold
time is such that when SDI and CNV are connected together,
chain mode is always selected.
In normal mode operation, the AD7985 offers the option of
forcing a start bit in front of the data bits. This start bit can be
used as a busy signal indicator to interrupt the digital host and
trigger the data reading. Otherwise, without a busy indicator,
the user must time out the maximum conversion time prior to
readback.
The busy indicator feature is enabled in CS mode if CNV or
SDI is low when the ADC conversion ends (see Figure 29 and
Figure 33). TURBO must be kept low for both digital interfaces.
When CNV is low, readback can occur during conversion or
acquisition, or it can be split across acquisition and conversion,
as described in the following sections.
A discontinuous SCK is recommended because the part is selected
with CNV low, and SCK activity begins to clock out data.
Note that in the following sections, the timing diagrams indicate
digital activity (SCK, CNV, SDI, and SDO) during the conversion.
However, due to the possibility of performance degradation, digi-
tal activity should occur only prior to the safe data reading time,
tDATA, because the AD7985 provides error correction circuitry
that can correct for an incorrect bit decision during this time.
From tDATA to tCONV, there is no error correction, and conversion
results may be corrupted.
Similarly, tQUIET, the time from the last falling edge of SCK to
the rising edge of CNV, must remain free of digital activity.
The user should configure the AD7985 and initiate the busy
indicator (if desired in normal mode) prior to tDATA.
It is also possible to corrupt the sample by having SCK near the
sampling instant. Therefore, it is recommended that the digital
pins be kept quiet for approximately 20 ns before and 10 ns after
the rising edge of CNV, using a discontinuous SCK whenever
possible to avoid any potential performance degradation.
相關PDF資料 |
PDF描述 |
|---|---|
| RPP20-2412D/N | CONV DC/DC 20W 18-36VIN +/-12V |
| EBA22DTKH-S288 | CONN EDGECARD 44POS .125 EXTEND |
| 0982660123 | CBL 12POS 0.5MM JMPR TYPE A 4" |
| RPP20-2405S/N | CONV DC/DC 20W 18-36VIN 05VOUT |
| EBM28DCTN | CONN EDGECARD 56POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7986EBZ | 功能描述:BOARD EVAL FOR AD7986 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7988-5SDZ | 功能描述:BAORD EVAL FOR AD7988-5 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7991EBZ | 功能描述:BOARD EVAL FOR AD7991 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7991EBZ | 制造商:Analog Devices 功能描述:AD7991, ADC, I2C, EVALUATION BOARD |
| EVAL-AD7992CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:2-Channel, 12-Bit ADC with I2C-Compatible |
發布緊急采購，3分鐘左右您將得到回復。