- 您現在的位置：買賣IC網 > PDF目錄16594 > EVAL-AD8403SDZ (Analog Devices Inc)BOARD EVAL FOR AD8403 PDF資料下載
參數資料
| 型號： | EVAL-AD8403SDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 17/32頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD8403 |
| 標準包裝： | 1 |
| 主要目的： | 數字電位器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD8403 |
| 主要屬性： | 4 通道，256 位置 |
| 次要屬性： | SPI 接口 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD8400/AD8402/AD8403
Rev. E | Page 24 of 32
APPLICATIONS
INVERTING GAIN (V/V)
256
128
0
0.1
1
10
96
64
32
160
192
224
DI
G
IT
A
L
CO
DE
(D
eci
mal
)
01
09
2-
05
3
The digital potentiometer (RDAC) allows many of the applica-
tions of a mechanical potentiometer to be replaced by a solid-
state solution offering compact size and freedom from vibration,
shock, and open contact problems encountered in hostile
environments. A major advantage of the digital potentiometer
is its programmability. Any settings can be saved for later recall
in system memory.
The two major configurations of the RDAC include the
potentiometer divider (basic 3-terminal application) and
the rheostat (2-terminal configuration) connections shown
Certain boundary conditions must be satisfied for proper
AD8400/AD8402/AD8403 operation. First, all analog signals
must remain within the GND to VDD range used to operate the
single-supply AD8400/AD8402/AD8403. For standard
potentiometer divider applications, the wiper output can be
used directly. For low resistance loads, buffer the wiper with
a suitable rail-to-rail op amp such as the OP291 or the OP279.
Second, for ac signals and bipolar dc adjustment applications,
a virtual ground is generally needed. Whichever method is used
to create the virtual ground, the result must provide the necessary
sink and source current for all connected loads, including
adequate bypass capacitance. Figure 41 shows one channel of
the AD8402 connected in an inverting programmable gain
amplifier circuit. The virtual ground is set at 2.5 V, which allows
the circuit output to span a ±2.5 V range with respect to virtual
ground. The rail-to-rail amplifier capability is necessary for the
widest output swing. As the wiper is adjusted from its midscale
reset position (80H) toward the A terminal (code FFH), the
voltage gain of the circuit is increased in successively larger
increments. Alternatively, as the wiper is adjusted toward the B
terminal (code 00H), the signal becomes attenuated. The plot in
Figure 54 shows the wiper settings for a 100:1 range of voltage
gain (V/V). Note the ±10 dB of pseudologarithmic gain around
0 dB (1 V/V). This circuit is mainly useful for gain adjustments
in the range of 0.14 V/V to 4 V/V; beyond this range the step
sizes become very large, and the resistance of the driving circuit
can become a significant term in the gain equation.
Figure 54. Inverting Programmable Gain Plot
ACTIVE FILTER
The state variable active filter is one of the standard circuits
used to generate a low-pass, high-pass, or band-pass filter.
The digital potentiometer allows full programmability of the
frequency, gain, and Q of the filter outputs. Figure 55 shows
the filter circuit using a 2.5 V virtual ground, which allows a
±2.5 VP input and output swing. RDAC2 and RDAC3 set the
LP, HP, and BP cutoff and center frequencies, respectively.
These variable resistors should be programmed with the same
data (as with ganged potentiometers) to maintain the best
Circuit Q. Figure 56 shows the measured filter response at the
band-pass output as a function of the RDAC2 and RDAC3
settings that produce a range of center frequencies from 2 kHz
to 20 kHz. The filter gain response at the band-pass output is
shown in Figure 57. At a center frequency of 2 kHz, the gain is
adjusted over a 20 dB to +20 dB range determined by RDAC1.
Circuit Q is adjusted by RDAC4. For more detailed reading on
the state variable active filter, see Analog Devices’ application
note AN-318.
A1
RDAC1
VIN
B
A2
A3
A4
RDAC4
B
10k
Ω
10k
Ω
OP279 × 2
RDAC2
RDAC3
B
0.01
μF
0.01
μF
BAND-
PASS
HIGH-
PASS
LOW-
PASS
0
1
092-
054
Figure 55. Programmable State Variable Active Filter
相關PDF資料 |
PDF描述 |
|---|---|
| EEM25DRST | CONN EDGECARD 50POS DIP .156 SLD |
| EVAL-AD5111SDZ | BOARD EVAL FOR AD5111 |
| H3BBH-5036G | IDC CABLE - HSR50H/AE50G/HSR50H |
| H8MMH-2636M | DIP CABLE - HDM26H/AE26M/HDM26H |
| ESM10DRSN | CONN EDGECARD 20POS DIP .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD9388AFEZ_1 | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits) |
| EVAL-AD9388AFEZ_2 | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits) |
| EVAL-AD9388AFEZ_3 | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits) |
| EVAL-AD9393-ABZ | 功能描述:EVAL BOARD AD9393 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| EVAL-AD9393-AKZ | 功能描述:EVAL KIT 9393 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
發布緊急采購，3分鐘左右您將得到回復。