參數資料
型號： EVAL-ADM3053EBZ
廠商： Analog Devices Inc
文件頁數： 5/20頁
文件大小： 0K
描述： BOARD EVAL FOR ADM3053EBZ
標準包裝： 1
系列： IsoPower®, iCoupler®
主要目的： 接口，CAN
已用 IC / 零件： ADM3053
已供物品： 板
Data Sheet
ADM3053
Rev. B | Page 13 of 20
CIRCUIT DESCRIPTION
CAN TRANSCEIVER OPERATION
A CAN bus has two states called dominant and recessive. A
dominant state is present on the bus when the differential
voltage between CANH and CANL is greater than 0.9 V. A
recessive state is present on the bus when the differential voltage
between CANH and CANL is less than 0.5 V. During a dominant
bus state, the CANH pin is high, and the CANL pin is low.
During a recessive bus state, both the CANH and CANL pins
are in the high impedance state.
Pin 18 (RS) allows two different modes of operation to be
selected: high-speed and slope control. For high-speed
operation, the transmitter output transistors are simply
switched on and off as fast as possible. In this mode, no
measures are taken to limit the rise and fall slopes. A shielded
cable is recommended to avoid EMI problems. High-speed
mode is selected by connecting Pin 18 to ground.
Slope control mode allows the use of an unshielded twisted pair
or a parallel pair of wires as bus lines. To reduce EMI, the rise
and fall slopes should be limited. The rise and fall slopes can be
programmed with a resistor connected from Pin 18 to ground.
The slope is proportional to the current output at Pin 18.
SIGNAL ISOLATION
The ADM3053 signal isolation is implemented on the logic side of
the interface. The part achieves signal isolation by having a
digital isolation section and a transceiver section (see Figure 1).
Data applied to the TxD pin referenced to logic ground (GND1)
are coupled across an isolation barrier to appear at the transceiver
section referenced to isolated ground (GND2). Similarly, the
single-ended receiver output signal, referenced to isolated
ground in the transceiver section, is coupled across the isolation
barrier to appear at the RxD pin referenced to logic ground
(GND1). The signal isolation is powered by the VIO pin and
allows the digital interface to 3.3 V or 5 V logic.
POWER ISOLATION
The ADM3053 power isolation is implemented using an
iso
Power integrated isolated dc-to-dc converter. The dc-to-dc
converter section of the ADM3053 works on principles that are
common to most modern power supplies. It is a secondary side
controller architecture with isolated pulse-width modulation
(PWM) feedback. VCC power is supplied to an oscillating circuit
that switches current into a chip-scale air core transformer.
Power transferred to the secondary side is rectified and regulated to
5 V. The secondary (VISO) side controller regulates the output by
creating a PWM control signal that is sent to the primary (VCC)
side by a dedicated iCoupler data channel. The PWM modulates
the oscillator circuit to control the power being sent to the
secondary side. Feedback allows for significantly higher power
and efficiency.
TRUTH TABLES
The truth tables in this section use the abbreviations found in
Table 9. Truth Table Abbreviations
Letter
Description
H
High level
L
Low level
X
Don’t care
Z
High impedance (off)
I
Indeterminate
NC
Not connected
Table 10. Transmitting
Supply Status
Input
Outputs
VIO
VCC
TxD
Bus State
CANH
CANL
On
L
Dominant
H
L
On
H
Recessive
Z
On
Floating
Recessive
Z
Off
On
X
Recessive
Z
On
Off
L
Indeterminate
I
Table 11. Receiving
Supply Status
Inputs
Output
VIO
VCC
VID = CANH CANL
Bus State
RxD
On
≥ 0.9 V
Dominant
L
On
≤ 0.5 V
Recessive
H
On
0.5 V < VID < 0.9 V
I
On
Inputs open
Recessive
H
Off
On
I
On
Off
H
1
X = don’t care.
THERMAL SHUTDOWN
The ADM3053 contains thermal shutdown circuitry that protects
the part from excessive power dissipation during fault conditions.
Shorting the driver outputs to a low impedance source can
result in high driver currents. The thermal sensing circuitry
detects the increase in die temperature under this condition and
disables the driver outputs. This circuitry is designed to disable
the driver outputs when a die temperature of 150°C is reached.
As the device cools, the drivers are reenabled at a temperature of
140°C.
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY
The digital signals transmit across the isolation barrier using
i
Coupler technology. This technique uses chip-scale transformer
windings to couple the digital signals magnetically from one
side of the barrier to the other. Digital inputs are encoded into
waveforms that are capable of exciting the primary transformer
相關PDF資料
PDF描述
VE-B1H-EW CONVERTER MOD DC/DC 52V 100W
ZXRE4041ERSTOB IC VREF SHUNT PREC 1.225V TO92-3
H2F1.18BK 2:1 FAB HEATSHRINK BLK 30MM 100'
EBM24DRKF-S13 CONN EDGECARD 48POS .156 EXTEND
H1BXH-2636G IDC CABLE - HSR26H/AE26G/X
相關代理商/技術參數
參數描述
EVAL-ADM3054EBZ 功能描述:EVAL BOARD FOR ADM3054 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
EVAL-ADM3251EEB1Z 功能描述:BOARD EVALUATION FOR ADM3251 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:isoPower® 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP
EVAL-ADM3251EEBZ 功能描述:BOARD EVALUATION ADM3251 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:isoPower® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
EVAL-ADM3252EEBZ 功能描述:BOARD EVAL FOR ADM3252E RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-ADM4168EEBZ 功能描述:界面開發工具 EVALUATION BOARD RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*