- 您現在的位置：買賣IC網 > PDF目錄375718 > FAN1585AM15X (FAIRCHILD SEMICONDUCTOR CORP) 5A Adjustable/Fixed Low Dropout Linear Regulator PDF資料下載
參數資料
| 型號： | FAN1585AM15X |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 5A Adjustable/Fixed Low Dropout Linear Regulator |
| 中文描述： | 1.5 V FIXED POSITIVE LDO REGULATOR, 1.3 V DROPOUT, PSSO3 |
| 封裝： | PLASTIC, TO-263, 3 PIN |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 63K |
| 代理商： | FAN1585AM15X |
FAN1585A
PRODUCT SPECIFICATION
6
REV. 1.1.5 11/7/03
Applications Information
General
The FAN1585A and FAN1585A-1.5 are three-terminal regu-
lators optimized for GTL+ V
TT
termination and logic appli-
cations. These devices are short-circuit protected and offer
thermal shutdown to turn off the regulator when the junction
temperature exceeds about 150°C. The FAN1585A series
provides low dropout voltage and fast transient response.
Frequency compensation uses capacitors with low ESR
while still maintaining stability. This is critical in addressing
the needs of low voltage high speed microprocessor buses
like GTL+.
Stability
The FAN1585A series requires an output capacitor as a part
of the frequency compensation. It is recommended to use a
22μF solid tantalum or a 100 μF aluminum electrolytic on
the output to ensure stability. The frequency compensation of
these devices optimizes the frequency response with low
ESR capacitors. In general, it is suggested to use capacitors
with an ESR of <300m
. It is also recommended to use
bypass capacitors such as a 22μF tantalum or a 100μF alumi-
num on the adjust pin of the FAN1585A for low ripple and
fast transient response. When these bypassing capacitors are
not used at the adjust pin, larger values of output capacitors
provide equally good results. Refer to Typical Performance
Characteristics for graph of stability of output capacitance
ESR vs load current.
Protection Diodes
In normal operation, the FAN1585A series does not require
any protection diodes. For the FAN1585A, internal resistors
limit internal current paths on the adjust pin. Therefore, even
with bypass capacitors on the adjust pin, no protection diode
is needed to ensure device safety under short-circuit condi-
tions.
A protection diode between the input and output pins is
usually not needed. An internal diode between the input and
the output pins on the FAN1585A series can handle micro-
second surge currents of 50A to 100A. Even with large value
output capacitors it is difficult to obtain those values of surge
currents in normal operation. Only with large values of output
capacitance, such as 1000μF to 5000μF, and with the input
pin instantaneously shorted to ground can damage occur. A
crowbar circuit at the input can generate those levels of cur-
rent; a diode from output to input is then recommended, as
shown in Figure 10. Usually, normal power supply cycling
or system “hot plugging and unplugging” will not generate
current large enough to do any damage.
The adjust pin can be driven on a transient basis ±7V with
respect to the output, without any device degradation. As
with any IC regulator, exceeding the maximum input-to-
output voltage differential causes the internal transistors to
break down and none of the protection circuitry is then func-
tional.
Figure 10. Optional Protection
Ripple Rejection
In applications that require improved ripple rejection, a
bypass capacitor from the adjust pin of the FAN1585A to
ground reduces the output ripple by the ratio of V
OUT
/1.25V.
The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1 (typically in
the range of 100
to 120
) in the feedback divider network
in Figure 10. Therefore, the value of the required adjust pin
capacitor is a function of the input ripple frequency. For
example, if R1 equals 100
and the ripple frequency equals
120Hz, the adjust pin capacitor should be 22μF. At 10kHz,
only 0.22μF is needed.
Output Voltage
The FAN1585A regulator develops a 1.25V reference volt-
age between the output pin and the adjust pin (see Figure
11). Placing a resistor R1 between these two terminals
causes a constant current to flow through R1 and down
through R2 to set the overall output voltage. Normally, this
current is the specified minimum load current of 10mA.
The current out of the adjust pin adds to the current from R1
and is typically 35μA. Its output voltage contribution is
small and only needs consideration when a very precise out-
put voltage setting is required.
FAN1585A
ADJ
C
ADJ
R2
R1
+
C2
22
μ
F
V
OUT
+
C1
22
μ
F
+
IN
OUT
D1
1N4002
(OPTIONAL)
V
IN
FAN1585A-1.5
IN
GND
C2
22
μ
F
V
OUT
C1
22
μ
F
+
+
OUT
D1
1N4002
(OPTIONAL)
V
IN
相關PDF資料 |
PDF描述 |
|---|---|
| FAN1585AM18X | 5A Adjustable/Fixed Low Dropout Linear Regulator |
| FAN1585A | 5.4A Adjustable/Fixed Low Dropout Linear Regulator(5.4安培電流輸出可調節的低壓差線性穩壓器) |
| FAN1587AM15X | 3A Adjustable/Fixed Low Dropout Linear Regulator |
| FAN1587AM33X | 3A Adjustable/Fixed Low Dropout Linear Regulator |
| FAN1587AT | 3A Adjustable/Fixed Low Dropout Linear Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN1585AM18X | 功能描述:低壓差穩壓器 - LDO 5a Linear Regulator adj/Fixed LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| FAN1585AMC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:VOLT REGULATOR|ADJUSTABLE|+1.25 TO +5.6V|BIPOLAR|SIP|3PIN|PLASTIC |
| FAN1585AMC-1.5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Positive Fixed Voltage Regulator |
| FAN1585AMC15X | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:5A Adjustable/Fixed Low Dropout Linear Regulator |
| FAN1585AMC15X_36 | 功能描述:低壓差穩壓器 - LDO 5a Linear Regulator adj/Fixed LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。