- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5093 (Fairchild Semiconductor Corporation) Two Phase Interleaved Synchronous Buck Converter for VRM 9.x Applications PDF資料下載
參數資料
| 型號： | FAN5093 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | Two Phase Interleaved Synchronous Buck Converter for VRM 9.x Applications |
| 中文描述： | 兩相交錯同步降壓轉換器的電源模組采用9.x中的應用 |
| 文件頁數： | 12/17頁 |
| 文件大?。?/td> | 578K |
| 代理商： | FAN5093 |
FAN5093
PRODUCT SPECIFICATION
12
REV. 1.1.0 3/27/03
Figure 3. Implementing E*-mode Control
Note:
The charge pump for the HIDRVs should be based on
the “B” phase of the FAN5093, since the “A” phase is off in
E*-mode.
Internal Voltage Reference
The reference included in the FAN5093 is a precision band-
gap voltage reference. Its internal resistors are precisely
trimmed to provide a near zero temperature coefficient (TC).
Based on the reference is the output from an integrated 5-bit
DAC. The DAC monitors the 5 voltage identification pins,
VID0-4, and scales the reference voltage from 1.100V to
1.850V in 25mV steps.
BYPASS Reference
The internal logic of the FAN5093 runs on 5V. To permit the
IC to run with 12V only, it produces 5V internally with a
linear regulator, whose output is present on the BYPASS pin.
This pin should be bypassed with a 100nF capacitor for noise
suppression. The BYPASS pin should not have any external
load attached to it.
Dynamic Voltage Adjustment
The FAN5093 can have its output voltage dynamically
adjusted to accommodate low power modes. The designer
must ensure that the transitions on the VID lines all occur
simultaneously (within less than
500
nsec) to avoid false codes
generating undesired output voltages. The Power Good flag
tracks the VID codes, but has a 500μsec delay transitioning
from high to low; this is long enough to ensure that there will
not be any glitches during dynamic voltage adjustment.
Power Good (PWRGD)
The FAN5093 Power Good function is designed in accor-
dance with the Pentium IV DC-DC converter specifications
and provides a continuous voltage monitor on the VFB pin.
The circuit compares the VFB signal to the VREF voltage
and outputs an active-low interrupt signal to the CPU should
the power supply voltage deviate more than -12% of its nom-
inal setpoint. The Power Good flag provides no control func-
tions to the FAN5093.
Output Enable/Soft Start (ENABLE/SS)
The FAN5093 will accept an open collector/TTL signal for
controlling the output voltage. The low state disables the
output voltage. When disabled, the PWRGD output is in the
low state.
Even if an enable is not required in the circuit, this pin
should have attached a capacitor (typically 100nF) to soft-
start the switching. A softstart capacitor may be approxi-
mately chosen by the formula:
where: t
D
is the delay time before the output starts to ramp
t
R
is the ramp time of the output
C
SS
= softstart cap
V
OUT
= nominal output voltage
However, C must be
≥
100nF.
Programmable Active Droop
The FAN5093 features Programmable Active Droop: as
the output current increases, the output voltage drops propor-
tionately an amount that can be programmed with an exter-
nal resistor. This feature is offered in order to allow
maximum headroom for transient response of the converter.
The current is sensed losslessly by measuring the voltage
across the low-side MOSFET during its on time. Consult the
section on current sensing for details. The droop is adjusted
by the droop resistor changing the gain of the current loop.
Note that this method makes the droop dependent on the
temperature and initial tolerance of the MOSFET, and the
droop must be calculated taking account of these tolerances.
Given a maximum output current, the amount of droop can
be programmed with a resistor to ground on the droop pin,
according to the formula
with V
Droop
the desired droop voltage, RT the oscillator
resistor, I
max
the output current at which the droop is desired,
and R
DS, on
the on-state resistance of one phase’s low-side
MOSFET.
Important Note!
The oscillator frequency must be selected
before selecting the droop resistor, because the value of R
T
is
used in the calculation of R
Droop
.
Over-Voltage Protection
The FAN5093 constantly monitors the output voltage for
protection against over-voltage conditions. If the voltage at
FAN5098, Pin 6
(Bypass)
FAN5098, Pin 21
(Droop, E*)
2N3906
HI=E*MODE
2N3904
1K
10K
10K
10K
R
DROOP
t
D
C
A
--------------
1.7
---------------------------------------------------------
0.9074
V
+
(
)
=
t
R
C
A
--------------
V
----------------------------
0.9
IN
=
R
Droop
(
)
V
I
max
R
DS on
------------------------------------
=
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5094 | Multi-Phase Interleaved Buck Converter |
| FAN5098 | Two Phase Interleaved Synchronous Buck Converter for AMD Hammer⑩ |
| FAN5109 | Dual Bootstrapped 12V MOSFET Driver |
| FAN5109MX | Terminal Block; No. of Positions:9; Pitch Spacing:0.197"; Mounting Type:PC Board RoHS Compliant: Yes |
| FAN5182 | Adjustable Output 1, 2, or 3-Phase Synchronous Buck Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5093MTC | 功能描述:直流/直流開關轉換器 Sync Buck Converter 2Phs Interleaved RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| FAN5093MTC_Q | 功能描述:DC/DC 開關控制器 Sync Buck Converter 2Phs Interleaved RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5093MTCX | 功能描述:DC/DC 開關控制器 Sync Buck Converter 2Phs Interleaved RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5094 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Multi-Phase Interleaved Buck Converter |
| FAN5094MTC | 功能描述:直流/直流開關轉換器 Buck Converter Hi Cur Sys Voltage RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。