- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5234MTCX (FAIRCHILD SEMICONDUCTOR CORP) Mobile-Friendly PWM/PFM Controller PDF資料下載
參數資料
| 型號： | FAN5234MTCX |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Mobile-Friendly PWM/PFM Controller |
| 中文描述： | SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | TSSOP-16 |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 537K |
| 代理商： | FAN5234MTCX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁
FAN5234
PRODUCT SPECIFICATION
REV. 1.0.10 5/3/04
9
This region is also associated with phase ‘bump’ or reduced
phase shift. The amount of phase shift reduction depends the
width of the region of flat gain and has a maximum value of
90 degrees. To further simplify the converter compensation,
the modulator gain is kept independent of the input voltage
variation by providing feed-forward of VIN to the oscillator
ramp.
The zero frequency, the amplifier high frequency gain and
the modulator gain are chosen to satisfy most typical appli-
cations. The crossover frequency will appear at the point
where the modulator attenuation equals the amplifier high
frequency gain. The only task that the system designer has to
complete is to specify the output filter capacitors to position
the load main pole somewhere within one decade lower than
the amplifier zero frequency. With this type of compensation
plenty of phase margin is easily achieved due to zero-pole
pair phase ‘boost’.
Conditional stability may occur only when the main load
pole is positioned too much to the left side on the frequency
axis due to excessive output filter capacitance. In this case,
the ESR zero placed within the 10kHz...50kHz range gives
some additional phase ‘boost’. Fortunately, there is an oppo-
site trend in mobile applications to keep the output capacitor
as small as possible.
Protection
The converter output is monitored and protected against
extreme overload, short circuit, over-voltage and under-
voltage conditions.
A sustained overload on an output sets the PGOOD pin low
and latches-off the whole chip. Operation can be restored by
cycling the VCC voltage or by toggling the EN pin.
If VOUT drops below the under-voltage threshold, the chip
shuts down immediately.
Over-Current sensing
If the circuit's current limit signal (“ILIM det” as shown in
Figure 4) is high at the beginning of a clock cycle, a
pulse-skipping circuit is activated and HDRV is inhibited.
The circuit continues to pulse skip in this manner for the next
8 clock cycles. If at any time from the 9
th
to the 16
th
clock
cycle, the "ILIM det" is again reached, the over-current
protection latch is set, disabling the chip. If "ILIM det" does
not occur between cycle 9 and 16, normal operation is
restored and the over-current circuit resets itself.
Figure 7. Over-Current protection waveforms
Over-Voltage / Under-Voltage Protection
Should the VSEN voltage exceed 120% of VREF (0.9V) due
to an upper MOSFET failure, or for other reasons, the
overvoltage protection comparator will force LDRV high.
This action actively pulls down the output voltage and, in the
event of the upper MOSFET failure, will eventually blow the
battery fuse. As soon as the output voltage drops below the
threshold, the OVP comparator is disengaged.
This OVP scheme provides a ‘soft’ crowbar function which
helps to tackle severe load transients and does not invert the
output voltage when activated — a common problem for
latched OVP schemes.
Similarly, if an output short-circuit or severe load transient
causes the output to droop to less than 75% of its regulation
set point. Should this condition occur, the regulator will shut
down.
Over-Temperature Protection
The chip incorporates an over temperature protection circuit
that shuts the chip down when a die temperature of about
150C is reached. Normal operation is restored at die tem-
perature below 125C with internal Power On Reset asserted,
resulting in a full soft-start cycle.
Design and Component Selection
Guidelines
As an initial step, define operating input voltage range,
output voltage, minimum and maximum load currents for the
controller.
For the examples in the following discussion, we will be
selecting components for:
VIN from 5V to 20V
V
OUT
= 1.8V @ I
LOAD(MAX)
= 3.5A
1
2
3
CH1 5.0V
CH3 2.0A
CH2 100mV
M 10.0
μ
s
IL
PGOOD
8 CLK
VOUT
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5234QSC | Mobile-Friendly PWM/PFM Controller |
| FAN5234QSCX | Mobile-Friendly PWM/PFM Controller |
| FAN5234 | Terminal Block; Pitch Spacing:0.197"; Mounting Type:PC Board RoHS Compliant: Yes |
| FAN5235 | System Electronics Regulator for Mobile PCs |
| FAN5236MTC | Dual Mobile-Friendly DDR / Dual-output PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5234QSC | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5234QSC_Q | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5234QSCX | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5235 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:System Electronics Regulator for Mobile PCs |
| FAN5235_CAB3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。