- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5240QSC (FAIRCHILD SEMICONDUCTOR CORP) Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM PDF資料下載
參數資料
| 型號： | FAN5240QSC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM |
| 中文描述： | SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | QSOP-28 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 447K |
| 代理商： | FAN5240QSC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
PRODUCT SPECIFICATION
FAN5240
REV. 1.1.7 8/29/02
11
Additionally, the CPU power dissipation is also slightly
reduced as it is proportional to the applied voltage squared
and even slight voltage decrease translates to a measurable
reduction in power dissipated.
Figure 7. Effect of Active Droop on ESR
The processor regulation window including transients is
specified as +100mV..–50mV. To accommodate the droop,
the output voltage of the converter is raised by about 30mV
at no load.
The converter response to the load step is shown in Figure 8.
At zero load current, the output voltage is raised ~30mV
above nominal value of 1.5V. When the load current
increases, the output voltage droops down approximately
55mV. Due to use of Active Droop, the converter’s output
voltage adaptively changes with the load current allowing
better utilization of the regulation window.
Figure 8. Converter response to 5A load step
The current through each R
SENSE
resistor (ISNS) is sam-
pled shortly after LDRV is turned on. That current is held for
the remainder of the cycle, and then injected to produce an
offset to VCORE+ through the external 1K resistor (R6 in
Figure 1). This creates a voltage at the input to the error
amplifier that rises with increasing current, causing the regu-
lator’s output to droop as the current increases.
Gate Driver section
The gate control logic translates the internal PWM control
signal into the MOSFET gate drive signals providing
necessary amplification, level shifting and shoot-through
protection. Also, it has functions that help optimize the IC
performance over a wide range of operating conditions.
Since MOSFET switching time can vary dramatically from
type to type and with the input voltage, the gate control logic
provides adaptive dead time by monitoring the gate-to-
source voltages of both upper and lower MOSFETs. The
lower MOSFET drive is not turned on until the gate-to-
source voltage of the upper MOSFET has decreased to less
than approximately 1 volt. Similarly, the upper MOSFET is
not turned on until the gate-to-source voltage of the lower
MOSFET has decreased to less than approximately 1 volt.
This allows a wide variety of upper and lower MOSFETs to
be used without a concern for simultaneous conduction, or
shoot-through.
There must be a low – resistance, low – inductance path
between the driver pin and the MOSFET gate for the adap-
tive dead-time circuit to work properly. Any delay along that
path will subtract from the delay generated by the adaptive
dead-time circit and a shoot-through condition may occur.
Frequency Loop Compensation
Due to the implemented current mode control, the modulator
has a single pole response with -1 slope at frequency deter-
mined by load
where R
O
is load resistance, C
O
is load capacitance. For this
type of modulator Type 2 compensation circuit is usually
sufficient. To reduce the number of external components and
simplify the design task, the PWM controller has an inter-
nally compensated error amplifier. Figure 9 shows a Type 2
amplifier and its response along with the responses of a cur-
rent mode modulator and of the converter. The Type 2 ampli-
fier, in addition to the pole at the origin, has a zero-pole pair
that causes a flat gain region at frequencies between the zero
and the pole.
ILOAD
Vout
(no droop)
Vout
droop
≈
ESR
upper lim
lower lim
lower lim
V
ES
V
ES
upper lim
V
DROOP
I
R
SENSE
)
-------------------------------------------
=
(7)
F
PO
O
O
-----------------------
=
(8)
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5240QSCX | Multi-Phase PWM Controller for AMD Mobile Athlon TM and Duron TM |
| FAN5250 | Mobile Processor Core-Voltage Regulator |
| FAN5250QSC | Mobile Processor Core-Voltage Regulator |
| FAN5250QSCX | Mobile Processor Core-Voltage Regulator |
| FAN5307MPX | High-Efficiency Step-Down DC-DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5240QSCX | 功能描述:開關變換器、穩壓器與控制器 PWM Controller Two Phase RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5242_AAB3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5242MTC | 功能描述:開關變換器、穩壓器與控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5242MTCX | 功能描述:開關變換器、穩壓器與控制器 PWM Controller RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5242QSC | 功能描述:開關變換器、穩壓器與控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。