- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5250QSC (FAIRCHILD SEMICONDUCTOR CORP) Mobile Processor Core-Voltage Regulator PDF資料下載
參數資料
| 型號： | FAN5250QSC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Mobile Processor Core-Voltage Regulator |
| 中文描述： | SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封裝： | 0.150 INCH, MO-137, QSOP-24 |
| 文件頁數： | 9/17頁 |
| 文件大小： | 469K |
| 代理商： | FAN5250QSC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
FAN5250
REV. 1.1.6 3/12/03
9
Operation Mode Control
The mode-control circuit changes the converter’s mode of
operation based on the voltage polarity of the SW node when
the lower MOSFET is conducting and just before the upper
MOSFET turns on. For continuous inductor current, the SW
node is negative when the lower MOSFET is conducting and
the converters operate in fixed-frequency PWM mode as
shown in Figure 5. This mode of operation achieves high
efficiency at nominal load. When the load current decreases
to the point where the inductor current flows through the
lower MOSFET in the ‘reverse’ direction, the SW node
becomes positive, and the mode is changed to hysteretic,
which achieves higher efficiency at low currents by decreas-
ing the effective switching frequency.
A comparator handles the timing of the SW node voltage
sensing. A low level on the SW comparator output indicates
a negative SW voltage during the conduction time of the
lower MOSFET. A high level on the comparator output indi-
cates a positive SW voltage. To prevent accidental mode
change and “mode chatter”, the circuit must detect eight con-
secutive matching sign signals in a row before it changes
mode. If during the monitoring process the mismatch of volt-
age signs occurs, no decision to mode change will occur.
This same decision algorithm is used both for changing from
PWM to Hysteretic mode as well as from Hysteretic to
PWM mode.
PWM mode is sustained during all upward and downward
transitions commanded by either VID code change, or during
transitions from ALTV programmed voltage to VID code set
voltage, or vice versa, as well as in Soft-Start.
The boundary value of inductor current, where current
becomes discontinuous, can be estimated by the following
expression.
Hysteretic Mode
The mode change from hysteretic to PWM can be caused by
one of two events. One event is the same mechanism that
causes a PWM to hysteretic transition. But instead of look-
ing for eight consecutive positive occurrences on the SW
node it is looking for eight consecutive negative occurrences
on the SW node. The operation mode will be changed from
hysteretic to PWM when these eight consecutive pulses
occur. This transition technique prevents jitter of the
operation mode at load levels close to boundary.
The other mechanism for changing from hysteretic to PWM
is due to a sudden increase in the output current. This step
load causes an instantaneous decrease in the output voltage
due to the voltage drop on the output capacitor ESR. If the
decrease causes the output voltage to drop below the hyster-
etic regulation level (20mV below V
SS
), the mode is changed
to PWM on the next clock cycle. This insures the full power
required by the increase in output current.
In hysteretic mode, the PWM comparator and the error
amplifier that provided control in PWM mode are inhibited
and the hysteretic comparator is activated. In this mode the
synchronous rectifier MOSFET is controlled in diode
emulation mode, where the voltage across it is monitored,
and it is switched off when its voltage goes positive (current
flowing back from the load) allowing the schottky diode to
block reverse conduction.
The hysteretic comparator initiates a PFM signal to turn on
UDRV when the output voltage falls below the lower
threshold (10mV below V
SS
) and terminates the PFM signal
when the output voltage rises over the higher threshold
(5mV above V
SS
).
I
LOAD DIS
)
V
2 F
SW
L
OUT
V
VIN
-------------–
)
V
OUT
=
(6)
Figure 5. Transitioning Between PWM and Hysteresis
PWM Mode
Hysteretic Mode
Hysteretic Mode
PWM Mode
1
2
3
4
5
6
7
8
V
CORE
I
L
0
V
CORE
I
L
0
1
2
3
4
5
6
7
8
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5250QSCX | Mobile Processor Core-Voltage Regulator |
| FAN5307MPX | High-Efficiency Step-Down DC-DC Converter |
| FAN5307S18X | High-Efficiency Step-Down DC-DC Converter |
| FAN5307SX | High-Efficiency Step-Down DC-DC Converter |
| FAN5307 | High-Efficiency Step-Down DC-DC Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5250QSC_Q | 功能描述:DC/DC 開關控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5250QSCX | 功能描述:DC/DC 開關控制器 Crusoe Processor Core Voltage RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5250QSCX_SM2E203 | 功能描述:IC REG MOBILE PROC CORE 24QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| FAN5307 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High-Efficiency Step-Down DC-DC Converter |
| FAN5307MP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。