參數資料
型號: FC100V20A-R
廠商: POWER-ONE INC
元件分類: 數據傳輸濾波器
英文描述: DATA LINE FILTER MODULE
文件頁數: 3/41頁
文件大?。?/td> 1387K
代理商: FC100V20A-R
MCD10059 Rev. 1.0
Page 11 of 41
www.power-one.com
F & FC Series DC-DC Converter Input Filters
F2410 & F4810, 0-45V/0-80V, 10 Amps, SMT Mount
caps to common line. Vertical scale: 10 dB/div, with zero dB
level marked by arrow.
Thermal Considerations
Because of low series internal DC resistance, the
F4810/F2410 filters generally do not require airflow
and/or derating to ambient temperatures up to 85 C,
if placed and interconnected as described below.
Good thermal design is consistent with appropriate
placement to gain additional heat exchange through
the I/O pins to the system board. For high
temperature operation in low airflow environments,
use of 1-2 oz copper for the external connection
pads and provision for some extra copper at all four
I/O pins is encouraged. Thermal derating data shown
were taken on special thermal board with each input
and output pin connected to 0.5 sq. in pad of 2 oz
copper.
To check filter thermal characteristic in an actual
system environment, attach a thermocouple to the
top of differential inductor, L2; it is the INDUCTOR
closest to OUT+ pin.
The maximum temperature at this test point should
not exceed 120 C, and a minimum of 5-10 C
headroom is suggested for better reliability.
A typical application schematic is shown in Fig. 5.
Either filter can be used to power one or more
converters. Maximum filter output current should be
limited 10 A - or less - depending upon system
thermal environment.
The required filter current drawn by the converter
loads, IREQ’d(Filter), will be the sum of the loads of all
connected converters:
IREQ’d(filter) = Σ[Pi,OUT/(VIN, min * ηi, min)]
[A]
where:
IREQ’d(filter)
maximum required filter current
Pi,OUT(converter)
converter output power, i=1, 2…
= Vi,OUT(converter) *
Ii,OUT(converter)
VIN, min
converter input voltage
ηi, min
converter minimum efficiency, i=1,
2,…
For applications requiring a filter current greater than
10 A, divide the converters into smaller groups and
use multiple filters. Do not connect filters in parallel.
Fig. 5: F4810 – Typical application
C6
C3
C7
Rload2
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
Converter
QmaXTMSeries
C9
C1
F4810
V
IN-
V
IN+
+48V
-48V
+Vout
-Vout
P3
P4
P1
P2
+
F1
12A
C2
C5
Rload1
Vin (+)
Vin (-)
ON/OFF
Vout (+)
Vout (-)
TRIM
SENSE (+)
SENSE (-)
(Top View)
Converter
QmaXTMSeries
C8
C4
(Top View)
Input Filter
For further information
regarding connection of CM
capacitors and other
pertinent layout and EMC
information, please refer to
the Layout Considerations
and EMI Considerations
Application notes.
DC-DC
Converter
(Top View)
DC-DC
Converter
(Top View)
相關PDF資料
PDF描述
FC100V20A-SG DATA LINE FILTER MODULE
FC100V20A-SRG DATA LINE FILTER MODULE
FC100V20A-SR DATA LINE FILTER MODULE
FC100V20A-S DATA LINE FILTER MODULE
FC100V5A-G DATA LINE FILTER MODULE
相關代理商/技術參數
參數描述
FC100V5A 功能描述:FILTER 5 AMP PC MOUNT RoHS:否 類別:濾波器 >> 線路濾波器 系列:FC RoHS指令信息:RoHS Material 標準包裝:1 系列:RSEN 濾波器類型:電源線 電壓 - 額定:250V 電流:150A 電感:- 安裝類型:底座安裝 端接類型:端接塊 其它名稱:RSEN2150
FC100V5A-G 功能描述:DC/DC轉換器 0-100Vin 5A 1500VDC Isolation RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
FC100V6A 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸:
FC100V6AG 制造商:Power-One 功能描述:DCDC,HAZMAT - Bulk
FC100V6A-G 功能描述:DC/DC轉換器 RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓(標稱): 輸出端數量:1 輸出電壓(通道 1):3.3 V 輸出電流(通道 1):600 mA 輸出電壓(通道 2): 輸出電流(通道 2): 安裝風格:SMD/SMT 封裝 / 箱體尺寸: