DO NOT
SCALE FROM
THIS PRINT
FJ-XX-X-XX-X
No OF POSITIONS
-05, -10, -15, -20, -25, -30
STYLE
-S: SINGLE ENDED
-D: DOUBLE ENDED
-R: REVERSE STIFFENER
LENGTH
-XX: "XX" INCHES .125 [3.18] INCH
(-S STYLE 2.500 [63.50] MIN)
(-D & -R STYLE 2.000 [50.80] MIN)
STRIP LENGTH
-2: .079 [2.00]
*-4: .157 [4.00]
-6: .236 [6.00]
* RECOMMENDED MATING WITH FC1
[1.000]
(No. OF POS. -1) x .03937
.01
REF
0.3
.021
REF
0.52
.207 5.26
REF
.004
REF
0.10
.012±.002 0.30±0.05
"A"
FS-20
C2
.03
REF
0.7
{No. OF POS x .03937 [1.0000]}
+ .03937 [1.0000] .005 [.13]
(SEE NOTE 2)
"C" .015 [.38] (SEE TABLE 1)
.005
(TYP)
0.13
(No. OF POS x .03937 [1.0000])
+.03937 [1.0000] .010 [.25]
(SEE NOTE 3)
LENGTH (SPECIFY IN -XX INCHES .125 [3.18]
.0256±.008 0.650±0.20
(TO BE MEASURED AT
BASE OF EXPOSED LEAD)
2 MAX SWAY
(TYP)
SECTION "A"-"A"
FC-XX-1.0
C3
C1
.01
REF
0.2
.0155
REF
0.393
.100 2.54
REF
.003
REF
0.08
"C" .030 [.76]
(SEE TABLE 1)
MACHINE BUILT (SEE NOTE 6)
-S: SINGLE ENDED
(FJ-10-S-XX-2 SHOWN)
SAME AS FIG 1 EXCEPT WHERE SHOWN
FIG. 4
FIG. 1
HAND BUILT (SEE NOTE 6)
-S: SINGLE ENDED
(FJ-10-S-XX-2 SHOWN)
C
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01 [.25]
2
.XXX: .005 [.13]
.XXXX: .0020 [.050]
MATERIAL:
.03937 [1.0000] FLEX CABLE JUMPER
BY:
FJ-XX-X-XX-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
KEVIN B
3/29/99
2
1
SHEET SCALE: 4:1
CONDUCTORS: TIN PLATED COPPER
INSULATION: POLYESTER
STIFFENER: POLYESTER
c:\enterprisevault\DWG\MISC\MKTG\FJ-XX-X-XX-X-MKT.SLDDRW
NOTES:
1.
REPRESENTS A CRITICAL DIMENSION.
2. MEASURE WHERE STIFFENER AND CABLE ARE ATTACHED.
3. MEASURED ALONG LENGTH OF CABLE, EXCEPT WHERE STIFFENER
IS ATTACHED TO CABLE.
4. NOTE DELETED.
5. STIFFENER IS TRIMMED TO CORRECT WIDTH.
6. HAND BUILT PARTS USE A BLUE STIFFENER., MACHINE BUILT PARTS
USE A BLACK STIFFENER.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
REVISION P