DO NOT
SCALE FROM
THIS PRINT
FJH-XX-X-XX-X
No OF POSITIONS
-06, -10, -15, -20, -24,
-25, -30, -40, -43, 50
(SEE TABLE 1)
STYLE
*-S: SINGLE ENDED
-D: DOUBLE ENDED
-R: REVERSE STIFFENER
LENGTH
-XX: "XX" INCHES 1/8 INCH
(-D & -R: 2.00" MINIMUM)
(-S: 2.50" MINIMUM)
STRIP LENGTH
-4: 4MM (.15748")
(SEE TABLE 1)
"A" .003
.0118 REF
LENGTH (SPECIFY IN -XX INCHES .125)
.157±.015
FC-XX-0.5
C
LENGTH (SPECIFY IN -XX INCHES .125)
.157±.015
-D: DOUBLE ENDED
(SAME AS FIG. 1, UNLESS STATED)
FIG 2
LENGTH (SPECIFY IN -XX INCHES .125)
.157±.015
FS-20
(SAME AS FIG. 1, UNLESS STATED)
FIG. 3
-R: REVERSE STIFFENER
.0138-.004
+.006
(TO BE MEASURED AT
BASE OF EXPOSED LEAD)
"B" POS. -1 x .0197
C
.0039 REF
.012±.002
.207 REF
.0126 REF
.023 REF
FS-20
FOR -S: ("XX" LENGTH + .591) .050
FOR -D & -R: ("XX" LENGTH + 1.181) .050
FC-XX-0.5
IN-PROCESS 1
.787
.207±.005
.433±.100
1.0225±.0075
FS-20
C
FC-XX-0.5
-S: SINGLE ENDED
(FJH-10-S-XX-ST2 SHOWN)
FS-20
IN-PROCESS 2
(TYP ON BOTH ENDS FOR -D & -R STYLES, ONE END -S STYLE)
FIG 1
* = AS OF 1/1/11, -S (SINGLE ENDED) AVAILABLE TO EXISTING
CUSTOMERS ONLY, ALL OTHERS WILL BE ASP`S.
L
C
NOTE:
1.
REPRESENTS A CRITICAL DIMENSION.
CRITICAL DIMENSION INSPECTION INSTRUCTION
TABLE
ASSEMBLY OPERATION IN-PROCESS INSPECTION
IN PROCESS 2
C3
TRIM STIFFENER
C1, C2, C4
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
.XX: .01
2
.XXX: .005
.XXXX: .0020
MATERIAL:
.5mm FLEX CABLE JUMPER
BY:
FJH-XX-X-XX-X
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
KEVIN B
6/28/00
1
SHEET SCALE: 3:1
CONDUCTORS: TIN PLATED COPPER
SURFACE FINISH EITHER BRIGHT TIN (99.9% SN)
OR MATTE TIN (95.5% SN, 3.5% AG, 1% CU)
INSULATION & STIFFENER: POLYESTER
c:\enterprisevault\DWG\MISC\MKTG\FJH-XX-X-XX-X-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
REVISION L