- 您現在的位置：買賣IC網 > PDF目錄67445 > FK2320-9RD1B1 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FK2320-9RD1B1 |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | METAL, CASE K02, MODULE |
| 文件頁數： | 4/31頁 |
| 文件大?。?/td> | 637K |
| 代理商： | FK2320-9RD1B1 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
12/31
Output Protection
Each output is protected against overvoltages which could
occur due to a failure of the internal control circuit. Voltage
suppressor diodes (which under worst case condition may
become a short circuit) provide the required protection. The
suppressor diodes are not designed to withstand externally
applied overvoltages. Overload at any of the outputs will
cause a shut-down of all outputs. A red LED indicates the
overload condition.
Parallel or Series Connection of Units
Single or double output units with equal nominal output
voltage can be connected in parallel without any precau-
tions using option T.
With option T (current sharing), all units share the current
approximately equally.
Single output units and/or main and second outputs of dou-
ble output units can be connected in series with any other
(similar) output.
Note:
– Parallel connection of double output units should always
include both, main and second output to maintain good
regulation of both outputs.
– Not more than 5 units should be connected in parallel.
– Series connection of second outputs without involving
their main outputs should be avoided as regulation may
be poor.
– The maximum output current is limited by the output with
the lowest current limitation if several outputs are con-
nected in series.
Thermal Considerations
If a converter is located in free, quasi-stationary air (con-
vection cooling) at the indicated maximum ambient tem-
perature
TA max (see table: Temperature specifications) and
is operated at its nominal input voltage and output power,
the temperature measured at the
Measuring point of case
temperature TC (see: Mechanical Data) will approach the
indicated value
TC max after the warm-up phase. However,
the relationship between
TA and TC depends heavily on the
conditions of operation and integration into a system. The
thermal conditions are influenced by input voltage, output
current, airflow and temperature of surrounding compo-
nents and surfaces.
TA max is therefore, contrary to TC max,
an indicative value only.
Caution: The installer must ensure that under all operat-
ing conditions
TC remains within the limits stated in the
table
Temperature specifications.
Notes: Sufficient forced cooling or an additional heat sink
allows
TA to be higher than 71°C (e.g. 85°C) if TC max is not
exceeded.
For -7 or -9 units at an ambient temperature
TA of 85
°C with
only convection cooling, the maximum permissible current
for each output is approx. 40% of its nominal value as per
figure.
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
50
60
70
80
90
100
Io/Io nom
TA [°C]
0.9
1.0
Forced cooling
05089
TA min
TC max
Convection cooling
Fig. 7
Output current derating versus temperature for -7 and -9
units.
Thermal Protection
A temperature sensor generates an internal inhibit signal
which disables the outputs if the case temperature exceeds
TC max. The outputs are automatically re-enabled if the tem-
perature drops below this limit.
It is recommended that continuous operation under simul-
taneous extreme worst case conditions of the following
three parameters be avoided: Minimum input voltage,
maximum output power and maximum temperature.
Uo1d
t d
Ur
t
Uo2d
<10
s
<10
s
Uo1
Uo2
Io1/Io1 nom
0
0.5
1
Io2/Io2 nom
05072
Fig. 8
Typical dynamic load regulation of Uo1 and Uo2
相關PDF資料 |
PDF描述 |
|---|---|
| FK2320-9RD2B1 | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK2540-7PD7T | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK2540-7PD9TB2 | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK2540-7RDDT | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| FK2540-9PB2 | 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FK2323-9R-B1 | 制造商:Power-One 功能描述:K Series 150 W 12 V Dual Output DC-DC Converter 制造商:POWER ONE 功能描述:K Series 150 W 12 V Dual Output DC-DC Converter |
| FK23451 | 制造商:Knowles 功能描述:RECEIVER BALANCED ARMATURE 制造商:Knowles 功能描述:RECEIVER, BALANCED ARMATURE 制造商:Knowles 功能描述:RECEIVER, BALANCED ARMATURE; Transducer Function:Receiver; Frequency Response Min:200Hz; Frequency Response Max:7kHz; Output Impedance:450ohm; External Height:1.93mm; External Width:5.00mm; External Depth:2.73mm; SVHC:No SVHC ;RoHS Compliant: Yes |
| FK-23451-000 | 功能描述:揚聲器與變頻器 5.00 X 2.73 X 1.93MM 95.5 SENS, 12S PORT RoHS:否 制造商:PUI Audio 產品:Speakers 類型:Electromagnetic 頻率:900 Hz to 12 kHz 聲壓級:88 dBA 阻抗:8 Ohms 功率額定值:1.2 W 形狀:Round 端接類型:Solder Pad 直徑:15 mm 長度: 寬度: 深度:4.4 mm 磁體材料:Neodymium Iron Boran (NdFeB) 圓錐體材料:Mylar |
| FK-23466-000 | 功能描述:揚聲器與變頻器 5.00 X 2.73 X 1.93MM 95.5 SENS, 12S PORT RoHS:否 制造商:PUI Audio 產品:Speakers 類型:Electromagnetic 頻率:900 Hz to 12 kHz 聲壓級:88 dBA 阻抗:8 Ohms 功率額定值:1.2 W 形狀:Round 端接類型:Solder Pad 直徑:15 mm 長度: 寬度: 深度:4.4 mm 磁體材料:Neodymium Iron Boran (NdFeB) 圓錐體材料:Mylar |
| FK-23989-000 | 功能描述:揚聲器與變頻器 5.00 X 2.73 X 1.93MM 95 SENS, 12N PORT RoHS:否 制造商:PUI Audio 產品:Speakers 類型:Electromagnetic 頻率:900 Hz to 12 kHz 聲壓級:88 dBA 阻抗:8 Ohms 功率額定值:1.2 W 形狀:Round 端接類型:Solder Pad 直徑:15 mm 長度: 寬度: 深度:4.4 mm 磁體材料:Neodymium Iron Boran (NdFeB) 圓錐體材料:Mylar |
發布緊急采購，3分鐘左右您將得到回復。