參數資料
型號: FK2540-9PD6B1
元件分類: 電源模塊
英文描述: 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
封裝: METAL, CASE K02, MODULE
文件頁數: 6/31頁
文件大小: 637K
代理商: FK2540-9PD6B1
Cassette Style
150 Watt DC-DC Converters
K Series
Edition 01/01.2000
14/31
Fig. 15
Typical output response as a function of inhibit control
Table 5: Inhibit characteristics
Characteristic
Conditions
min
typ
max Unit
Uinh Inhibit
Uo = on
Ui min…Ui max
–50
0.8
V
voltage
Uo = off
2.4
50
Iinh
Inhibit current
Uinh = 0
–400
A
tr
Rise time
30
ms
tf
Fall time
depending on
Io
0
t
0
Inhibit
1
0.1
1
Uo/Uo nom
tr
tf
06001
Sense Lines
(Only for single output units 5.1 V, 12 V, 15 V, 24 V)
This feature enables for compensation of voltage drops
across the connector contacts and if necessary, across the
load lines. If the sense lines are connected at the load
rather than directly at the connector, the user should ensure
that
Uo max (between Vo1+ and Vo1–) is not exceeded. We
recommend connecting the sense lines directly at the fe-
male connector.
For further information, please refer to:
Application Notes.
To ensure correct operation, both sense lines (S+ and S–)
should be connected to their respective power outputs
(Vo1+ and Vo1–) and the voltage difference between any
sense line and its respective power output pin (as meas-
ured on the connector) should not exceed the following val-
ues:
Table 6: Maximum voltage compensation allowed using
sense lines
Output
Total voltage difference
Voltage difference
voltage
between sense lines and
between
their respective outputs
Vo– and S–
5.1 V
< 0.5 V
< 0.25 V
12 V, 15 V
< 1.0 V
< 0.25 V
If the output voltages are increased above
Uo nom via R-in-
put control, option P setting, remote sensing or option T, the
output currents must be reduced accordingly so that
Po nom is not exceeded.
Note: The output terminals Vo1+ and Vo1– must always be
connected to the load before connecting the sense lines S+
and S–, otherwise the unit will be damaged.
Auxiliary Functions
i Inhibit for Remote On and Off
Note: With open i input: Output is disabled (
Uo = off).
The outputs of the module may be enabled or disabled by
means of a logic signal (TTL, CMOS, etc.) applied between
the inhibit input i and the negative pin of output 1 (Vo1–). In
systems with several units, this feature can be used, for ex-
ample, to control the activation sequence of the converters.
If the inhibit function is not required, connect the inhibit pin
18 to pin 14 to enable the outputs (active low logic, fail
safe). For output response refer to:
Hold-up Time and Out-
put Response.
Vi+
Vi–
Vo–
i
Vo+
Iinh
Uinh
06031
1.6
0.8
0
–0.8
–50
Uinh [V]
Iinh [mA]
–30
0
–10
10
30
50
2.0
1.2
0.4
–0.4
Uinh = 0.8 V
Uo = on
Uo = off
Uinh = 2.4 V
06032
Fig. 13
Definition of Uinh and Iinh.
Fig. 14
Typical inhibit current Iinh versus inhibit voltage Uinh
相關PDF資料
PDF描述
FK2660-7PTB2 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
FK2660-9PD3TB2 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
FK2660-9PD9TB2 2-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
FK1001-7PTB1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
FK1001-7RB1 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
FK25L 功能描述:FLAT SENSOR BETWEEN PACK PROBE RoHS:是 類別:測試設備 >> 測試引線 - 熱電偶,溫度探頭 系列:FK 標準包裝:1 系列:6543 類型:J 型熱電偶 使用:液體,半固體 尖端 - 類型:防浸漬 / 穿透式,圓頭 插頭類型:超微型(熱電偶插頭) 探針溫度范圍:-40 ~ 2000°F(-40 ~ 1093°C) 線纜長度:- 線纜絕緣:- 插頭顏色:黑 探針長度:12.000"(304.80mm) 探針材料:-
FK25M 功能描述:FLAT SENSOR BETWEEN PACK PROBE RoHS:是 類別:測試設備 >> 測試引線 - 熱電偶,溫度探頭 系列:FK 標準包裝:1 系列:6543 類型:J 型熱電偶 使用:液體,半固體 尖端 - 類型:防浸漬 / 穿透式,圓頭 插頭類型:超微型(熱電偶插頭) 探針溫度范圍:-40 ~ 2000°F(-40 ~ 1093°C) 線纜長度:- 線纜絕緣:- 插頭顏色:黑 探針長度:12.000"(304.80mm) 探針材料:-
FK25SM5 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | MOSFET | N-CHANNEL | 250V V(BR)DSS | 25A I(D) | TO-247VAR
FK25SM-5 制造商:Powerex Power Semiconductors 功能描述:DISCRETE MOSFET TO-3P
FK25SM-5(#B00) 制造商:Renesas Electronics Corporation 功能描述: