- 您現在的位置：買賣IC網 > PDF目錄382965 > FOA2322A (INFINEON TECHNOLOGIES AG) 3.2 Gbi t /s Laser Driver IC for Telecom and Datacom Applications PDF資料下載
參數資料
| 型號： | FOA2322A |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | 3.2 Gbi t /s Laser Driver IC for Telecom and Datacom Applications |
| 中文描述： | 3.2陸基攔截噸/ s的電信和數據通信應用激光驅動器集成電路 |
| 文件頁數： | 24/37頁 |
| 文件大小： | 542K |
| 代理商： | FOA2322A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
FOA2322A
Electrical Characteristics
Preliminary Data Sheet
20
2001-05
2.8
Laser and
V
CC
Supervising Circuit
If there is a laser fault (optical power deviates
±
1 dB) this signal is stored and indicated
by LF (logic high). The fault indication (LF) can be reset with low level at RSTN or with
high level at RST or with power down (
V
CC
<
V
CC
Reset Threshold) only. After power up,
LF will always be cleared. Disabling the laser by LEN does not influence a previous fault
indication by LF. The laser fault generation can be switched off by connecting CFDEL to
V
CC
. During RSTN is logic low or RST is logic high the circuit is in Reset state.
In case of changing RST = H or RSTN = L after laser fault recognition LF = H (after
t
FDEL
) there is an additional delay time implemented which has the same value as the
Power On Delay.
If the supply voltage is lower than the
V
CC
reset threshold the indicator Hardware Alarm
(HWA) is still at the low level and the circuit is in Reset state.
During Power On Delay the circuit is in Reset state too. The Power On Delay is defined
as the delay after
V
CC
voltage has risen above the
V
CC
reset threshold. This time can be
adjusted by an external capacitor at COSC (Mode 1). The Reset N-Output of the
MAX 809S Power Supervisor IC can be connected to RSTN to use the reset function of
the MAX 809S.
The laser control by RST and RSTN is fully redundant. This means only an AND
combination of RST = 0 / RSTN = 1 can switch the laser on. The OR combination of
RST = 1 / RSTN = 0 switches the laser off (see
Table 4
for clarification).
Table 4
shows the static states of these signals. Dynamic changes or delays due to
external delay capacitors are not shown.
Table 4
Laser Diode Currents Enable / Disable Signals
V
CC
< Reset
Threshold
V
CC
0
X
RST
LEN
RSTN
In Case of
Laser Fault
LDOFF Modulation
Enable
1)
1)
Internal signal
2)
After Power On Delay
3)
After
t
FDEL
4)
Sink current enabled = Low
Bias
Enable
1)
LF (high
active)
X
1
X
1
0
0
0
1
X
X
X
X
1
0
0
0
X
X
0
X
X
1
0
0
0
X
X
X
X
yes
no
2)
no
2)
1
1
3)
0
4)
0
0
0
1
3)
0
0
1
1
0
0
0
0
1
0
1
1
0
相關PDF資料 |
PDF描述 |
|---|---|
| FOA3251B1 | High Speed Clock and Data Recovery for Fiber Optic Applications |
| foa3251d | 2.5 Gb/s Laser Driver(2.5 Gb/s激光驅動器) |
| foa3251p | Clock & Data Recovery Chip CDR 2.5 - 2.66 Gbit/s, 3.3 to 5.0 V(時鐘及數據恢復芯片) |
| FOA41001B1 | Semiconductor Solutions for High Speed Communi cation and Fiber OpticApplications |
| FOA51001B1 | SSR OCMOS FET 150MA NO 6-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FOA-302 | 制造商:L COM 功能描述:ADPTR,METAL SC-FC SIMPLEX BRNZ |
| FOA-321 | 制造商:L-com Inc 功能描述:Fiber Optic Adapter Kit 制造商:L-com Inc 功能描述:ADPTR KIT, SC ST FC COUPLERS |
| FOA3251 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2.5 Gbit/s Clock and Data Recovery-3R Signal Regeneration |
| FOA3251B1 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:High Speed Clock and Data Recovery for Fiber Optic Applications |
| FOA-401 | 制造商:L-com Inc 功能描述:ADPTR,METAL ST-ST DUPLEX BRNZ |
發布緊急采購，3分鐘左右您將得到回復。