參數資料
型號： FT-MOD-4232HUB
廠商： FTDI, Future Technology Devices International Ltd
文件頁數： 8/45頁
文件大?。?/td> 0K
描述： MOD USB HS HUB & SERIAL I/F
標準包裝： 1
主要目的： 接口，USB 2.0 集線器
嵌入式： 否
已用 IC / 零件： FT4232H
主要屬性： USB 高速集線器，最多 3 下行 USB 端口
次要屬性： USB 供電
已供物品： 板
其它名稱： 768-1091
Copyright 2010 Future Technology Devices International Limited
16
Document No.: FT_000060
FT4232H QUAD HIGH SPEED USB TO MULTIPURPOSE UART/MPSSE IC
Datasheet Version 2.2
Clearance No.: FTDI#78
+1.8V LDO Regulator. The +1.8V LDO regulator generates the +1.8 volts for the core and the USB
transceiver cell. Its input (VREGIN) must be connected to a +3.3V external power source. It is also
recommended to add an external filtering capacitor to the VREGIN. There is no direct connection from the
+1.8V output (VREGOUT) and the internal functions of the FT4232H. The PCB must be routed to connect
VREGOUT to the pins that require the +1.8V including VREGIN.
UTMI PHY. The Universal Transceiver Macrocell Interface (UTMI) physical interface cell. This block
handles the Full speed / High Speed SERDES (serialise - deserialise) function for the USB TX/RX data. It
also provides the clocks for the rest of the chip. A 12 MHz crystal should be connected to the OSCI and
OSCO pins. A 12K Ohm resistor should be connected between REF and GND on the PCB.
The UTMI PHY functions include:
Supports 480 Mbit/s "High Speed" (HS)/ 12 Mbit/s “Full Speed” (FS), FS Only and "Low Speed"
(LS).
SYNC/EOP generation and checking.
Data and clock recovery from serial stream on the USB.
Bit-stuffing/unstuffing; bit stuff error detection.
Manages USB Resume, Wake Up and Suspend functions.
Single parallel data clock output with on-chip PLL to generate higher speed serial data clocks.
EEPROM Interface. When used without an external EEPROM the FT4232H defaults to a quad USB to an
asynchronous serial port device. Adding an external 93C46 (93C56 or 93C66) EEPROM allows
customization of USB VID, PID, Serial Number, Product Description Strings and Power Descriptor value
of the FT4232H for OEM applications. Other parameters controlled by the EEPROM include Remote Wake
Up, Soft Pull Down on Power-Off and I/O pin drive strength.
The EEPROM must be a 16 bit wide configuration such as a Microchip 93LC46B or equivalent capable of a
1Mbit/s clock rate at VCC = +3.00V to 3.6V. The EEPROM is programmable in-circuit over USB using a
utility program called MPROG available from FTDI’s web site (www.ftdichip.com). This allows a blank
part to be soldered onto the PCB and programmed as part of the manufacturing and test process.
If no EEPROM is connected (or the EEPROM is blank), the FT4232H will default to serial ports. The device
uses its built-in default VID (0403), PID (6011) Product Description and Power Descriptor Value. In this
case, the device will not have a serial number as part of the USB descriptor.
相關PDF資料
PDF描述
222K174-3/42-0 BOOT MOLDED
RHS0G561MCN1GS CAP ALUM 560UF 4V 20% SMD
187783-000 FEED THROUGH MOLDED SIZE 13
CP2104EK KIT EVAL FOR CP2104
GMM08DTAI CONN EDGECARD 16POS R/A .156 SLD
相關代理商/技術參數
參數描述
FTN0.25CL 功能描述:FLEXO THIN 1/4" 200' SPOOL RoHS:是 類別:線纜，導線 - 管理 >> 螺線形繞線，伸縮套管 系列:Flexo® Thin 標準包裝:25 系列:HR 類型:螺旋繞線（線束） 直徑:0.250"（6.35mm） 直徑 - 最大值:3.000"（76.2mm） 長度:100' (30.5m) 材質:聚四氟乙烯（PTFE） 特點:- 顏色:透明 其它名稱:11026017HR-8T(1/2)HR-8T(1/2)-NDHR8T(1/2)
FTN01 制造商:OTAX Corporation 功能描述:
FTN09 制造商:TE Connectivity 功能描述:SWITCH DPDT
FTN0904 功能描述:撥動開關 DPDT ON-ON 6 Amps Panel RoHS:否 制造商:C&K Components 觸點形式:DPDT 開關功能:ON - ON - ON 電流額定值: 電壓額定值 AC:20 V 電壓額定值 DC:20 V 功率額定值:0.4 VA 端接類型:V-Bracket 安裝風格: 端子密封:Epoxy 觸點電鍍:Gold 照明:Not Illuminated
FTN09G 制造商:TE Connectivity 功能描述:SWITCH DPDT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*