- 您現在的位置：買賣IC網 > PDF目錄1922 > FT232HL-REEL (FTDI, Future Technology Devices International Ltd)IC HS USB TO UART/FIFO 48LQFP PDF資料下載
參數資料
| 型號： | FT232HL-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 7/65頁 |
| 文件大小： | 0K |
| 描述： | IC HS USB TO UART/FIFO 48LQFP |
| 應用說明： | FT1248 Application Note |
| 標準包裝： | 1 |
| 通道數： | 1，UART |
| FIFO's： | 4kb |
| 規程： | RS232，RS422，RS485 |
| 電源電壓： | 1.62 V ~ 1.98 V，2.97 V ~ 3.63 V |
| 帶并行端口： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 標準包裝 |
| 其它名稱： | 768-1101-6 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁
Copyright 2012 Future Technology Devices International Limited
15
Document No.: FT_000288
FT232H SINGLE CHANNEL HI-SPEED USB TO MULTIPURPOSE UART/FIFO IC
Datasheet Version 1.8
Clearance No.: FTDI #199
3.5.2 FT232H pins used in an FT245 Synchronous FIFO Interface
The FT232H can be configured as a FT245 synchronous FIFO interface. When configured in this mode, the
pins used and the descriptions of the signals are shown in Table 3.7. To set this mode the external
EEPROM must be set to 245 modes. A software command (FT_SetBitMode) is then sent by the application
to the FTDI D2xx driver to tell the chip to enter 245 synchronous FIFO mode. In this mode, data is
written or read on the rising edge of the CLKOUT. Refer to Figure 4.4 for timing details.
Pin No.
Name
Type
FT245 Configuration Description
13,14,15,16,
17,18,19,20
ADBUS[7:0]
I/O
D7 to D0 bidirectional FIFO data. This bus is normally input
unless OE# is low.
21
RXF#
OUTPUT
When high, do not read data from the FIFO. When low, there
is data available in the FIFO which can be read by driving RD#
low. When in synchronous mode, data is transferred on every
clock that RXF# and RD# are both low. Note that the OE# pin
must be driven low at least 1 clock period before asserting
RD# low.
25
TXE#
OUTPUT
When high, do not write data into the FIFO. When low, data
can be written into the FIFO by driving WR# low. When in
synchronous mode, data is transferred on every clock that
TXE# and WR# are both low.
26
RD#
INPUT
Enables the current FIFO data byte to be driven onto D0...D7
when RD# goes low. The next FIFO data byte (if available) is
fetched from the receive FIFO buffer each CLKOUT cycle until
RD# goes high.
27
WR#
INPUT
Enables the data byte on the D0...D7 pins to be written into
the transmit FIFO buffer when WR# is low. The next FIFO data
byte is written to the transmit FIFO buffer each CLKOUT cycle
until WR# goes high.
28
SIWU#
INPUT
The Send Immediate / WakeUp signal combines two functions
on a single pin. If USB is in suspend mode (PWREN# = 1) and
remote wakeup is enabled in the EEPROM, strobing this pin
low will cause the device to request a resume on the USB Bus.
Normally, this can be used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed
low any data in the device RX buffer will be sent out over USB
on the next Bulk-IN request from the drivers regardless of the
pending packet size. This can be used to optimize USB transfer
speed for some applications. Tie this pin to VCCIO if not used.
29
CLKOUT
OUTPUT
60 MHz Clock driven from the chip. All signals should be
synchronized to this clock.
30
OE#
INPUT
Output enable when low to drive data onto D0-7. This should
be driven low at least 1 clock period before driving RD# low to
allow for data buffer turn-around.
Table 3.7 FT245 Synchronous FIFO Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.4
相關PDF資料 |
PDF描述 |
|---|---|
| FT232RL-REEL | IC USB FS SERIAL UART 28-SSOP |
| FT245BL-REEL | IC USB FS PARALLEL FIFO 32-LQFP |
| FT245RL-REEL | IC USB TO PARALLEL FIFO 28-SSOP |
| FT4232HQ-REEL | IC USB HS QUAD UART/SYNC 64-QFN |
| FUSB1500MHX | IC USB 2.0 TRANSCEIVER 16-MLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT232HL-TRAY | 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT232HQ-REEL | 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT232HQ-TRAY | 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT232R | 制造商:FTDI 制造商全稱:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface |
| FT232R_10 | 制造商:FTDI 制造商全稱:FTDI 功能描述:USB UART IC - Single chip USB to asynchronous serial data transfer interface |
發布緊急采購，3分鐘左右您將得到回復。