- 您現在的位置：買賣IC網 > PDF目錄1922 > FT245BL-REEL (FTDI, Future Technology Devices International Ltd)IC USB FS PARALLEL FIFO 32-LQFP PDF資料下載
參數資料
| 型號： | FT245BL-REEL |
| 廠商： | FTDI, Future Technology Devices International Ltd |
| 文件頁數： | 24/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC USB FS PARALLEL FIFO 32-LQFP |
| 標準包裝： | 1,000 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-LQFP |
| 供應商設備封裝： | 32-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
DS245BL Version 1.7
Future Technology Devices Intl. Ltd. 2005
Page 9 of 24
FT245BL USB FIFO ( USB - Parallel ) I.C.
POWER CONTROL GROUP
Pin#
Signal
Type
Description
10
PWREN#
OUT
Goes Low after the device is congured via USB, then high during USB suspend.
Can be used to control power to external logic using a P-Channel Logic Level
MOSFET switch. Enable the Interface Pull-Down Option in EEPROM when using
the PWREN# pin in this way.
11
SI / WU
IN
The Send Immediate / WakeUp signal combines two functions on a single pin. If
USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the
EEPROM , strobing this pin low will cause the device to request a resume on the
USB Bus. Normally, this can be used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed low any data in the
device TX buffer will be sent out over USB on the next Bulk-IN request from the
drivers regardless of the pending packet size. This can be used to optimise USB
transfer speed for some applications. Tie this pin to VCCIO if not used.
MISCELLANEOUS SIGNAL GROUP
Pin#
Signal
Type
Description
4
RESET#
IN
Can be used by an external device to reset the FT245BL. If not required, tie to
VCC.
5
RSTOUT#
OUT
Output of the internal Reset Generator. Stays high impedance for ~ 5ms after
VCC > 3.5V and the internal clock starts up, then clamps its output to the 3.3V
output of the internal regulator. Taking RESET# low will also force RSTOUT# to
drive low. RSTOUT# is NOT affected by a USB Bus Reset.
27
XTIN
IN
Input to 6MHz Crystal Oscillator Cell. This pin can also be driven by an external
6MHz clock if required. Note : Switching threshold of this pin is VCC/2, so if
driving from an external source, the source must be driving at 5V CMOS level or
a.c. coupled to centre around VCC/2.
28
XTOUT
OUT
Output from 6MHz Crystal Oscillator Cell. XTOUT stops oscillating during USB
suspend, so take care if using this signal to clock external logic.
31
TEST
IN
Puts device in I.C. test mode – must be tied to GND for normal operation.
相關PDF資料 |
PDF描述 |
|---|---|
| FT245RL-REEL | IC USB TO PARALLEL FIFO 28-SSOP |
| FT4232HQ-REEL | IC USB HS QUAD UART/SYNC 64-QFN |
| FUSB1500MHX | IC USB 2.0 TRANSCEIVER 16-MLP |
| FUSB2805MLX | TXRX USB2.0 HS OTG ULPI 32MLP |
| FXLA2203UMX | TRANSLATOR LEVEL DUAL 24UMLP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT245BL-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB FIFO ( USB - PARALLEL ) I.C. |
| FT245BM | 功能描述:先進先出 Obsolete See FT245RL RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| FT245BM-TRAY | 功能描述:USB 接口集成電路 Obsolete See FT245RL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT245BQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FT245BQ USB FIFO ( USB - Parallel ) I.C. |
| FT245BQ-REEL | 功能描述:USB 接口集成電路 USB to Parallel FIFO IC QFN-32 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。