- 您現在的位置：買賣IC網 > PDF目錄68996 > FW250C1 (LINEAGE POWER LLC) DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FW250C1 |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 1142K |
| 代理商： | FW250C1 |
12
Lineage Power
Data Sheet
April 2008
dc-dc Converters; 36 to 75 Vdc Input, 15 Vdc Output; 250 W to 300 W
FW250C1 and FW300C1 Power Modules:
Feature Descriptions (continued)
Synchronization (continued)
SYNC OUT Pin
This pin contains a clock signal referenced to the VI(–)
pin. The frequency of this signal will equal either the
module’s internal clock frequency or the frequency estab-
lished by an external clock applied to the SYNC IN pin.
When synchronizing several modules together, the
modules can be connected in a daisy-chain fashion
where the SYNC OUT pin of one module is connected
to the SYNC IN pin of another module. Each module in
the chain will synchronize to the frequency of the first
module in the chain.
To avoid loading effects, ensure that the SYNC OUT
pin of any one module is connected to the SYNC IN pin
of only one module. Any number of modules can be
synchronized in this daisy-chain fashion.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with an overtemperature shutdown circuit.
The shutdown circuit will not engage unless the unit is
operated above the maximum case temperature.
Recovery from overtemperature shutdown is
accomplished by cycling the dc input power off for at
least 1.0 second or toggling the primary referenced
on/off signal for at least 1.0 second.
Forced Load Sharing (Parallel Opera-
tion)
For either redundant operation or additional power
requirements, the power modules can be configured for
parallel operation with forced load sharing (see
Figure 17). For a typical redundant configuration,
Schottky diodes or an equivalent should be used to
protect against short-circuit conditions. Because of the
remote sense, the forward-voltage drops across the
Schottky diodes do not affect the set point of the
voltage applied to the load. For additional power
requirements, where multiple units are used to develop
combined power in excess of the rated maximum, the
Schottky diodes are not needed.
Good layout techniques should be observed for noise
immunity. To implement forced load sharing, the follow-
ing connections must be made:
n
The parallel pins of all units must be connected
together. The paths of these connections should be
as direct as possible.
n
All remote-sense pins should be connected to the
power bus at the same point, i.e., connect all
SENSE(+) pins to the (+) side of the power bus at the
same point and all SENSE(–) pins to the (–) side of
the power bus at the same point. Close proximity and
directness are necessary for good noise immunity.
When not using the parallel feature, leave the
PARALLEL pin open.
8-581 (F)
Figure 17. Wiring Configuration for Redundant
Parallel Operation
Power Good Signal
The PWR GOOD pin provides an open-drain signal
(referenced to the SENSE(–) pin) that indicates the
operating state of the module. A low impedance
(<100
Ω) between PWR GOOD and SENSE(–) indi-
cates that the module is operating. A high impedance
(>1 M
Ω) between PWR GOOD and SENSE(–) indi-
cates that the module is off or has failed. The PWR
GOOD pin can be pulled up through a resistor to an
external voltage to facilitate sensing. This external volt-
age level must not exceed 40 V, and the current into
the PWR GOOD pin during the low-impedance state
should be limited to 1 mA maximum.
CASE
ON/OFF
VI(+)
VI(–)
SENSE(+)
SENSE(–)
VO(+)
VO(–)
PARALLEL
CASE
ON/OFF
VI(+)
VI(–)
SENSE(+)
SENSE(–)
VO(+)
VO(–)
PARALLEL
相關PDF資料 |
PDF描述 |
|---|---|
| FW300C1 | DC-DC REG PWR SUPPLY MODULE |
| FW250G1 | DC-DC REG PWR SUPPLY MODULE |
| FW300G1 | DC-DC REG PWR SUPPLY MODULE |
| FW300A1-A | 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE |
| FW300C1 | 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FW250F1 | 功能描述:CONVERTER DC/DC 3.3V 165W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW250 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| FW250H1 | 功能描述:CONVERTER DC/DC 24V 250W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW250 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| FW250R1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter |
| FW250S6R0 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter |
| FW250-TL-E | 制造商:SANYO 功能描述:N+N 60V 3A 0.145 SOP8 Tape & Reel 制造商:SANYO Semiconductor Co Ltd 功能描述:MOSFET NN CH 60V 3A SOT96 制造商:Sanyo 功能描述:0 |
發(fā)布緊急采購，3分鐘左右您將得到回復。