- 您現在的位置：買賣IC網 > PDF目錄68996 > FW300A1 (LINEAGE POWER LLC) 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FW300A1 |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | MODULE-20 |
| 文件頁數： | 3/20頁 |
| 文件大小： | 593K |
| 代理商： | FW300A1 |
Lineage Power
11
Data Sheet
April 2008
dc-dc Converters; 36 to 75 Vdc Input, 5 Vdc Output; 250 W to 300 W
FW250A1 and FW300A1 Power Modules:
Feature Descriptions (continued)
Remote Sense (continued)
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim. Consult the factory if you
need to increase the output voltage more than the
above limitation.
The amount of power delivered by the module is
dened as the voltage at the output terminals multiplied
by the output current. When using remote sense and
trim, the output voltage of the module can be
increased, which at the same output current would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power.
8-651 (C).e
Figure 18. Effective Circuit Conguration for
Single-Module Remote-Sense Operation
Output Voltage Set-Point Adjustment (Trim)
Output voltage trim allows the user to increase or
decrease the output voltage set point of a module. This
is accomplished by connecting an external resistor
between the TRIM pin and either the SENSE(+) or
SENSE(–) pins. The trim resistor should be positioned
close to the module.
If not using the trim feature, leave the TRIM pin open.
With an external resistor between the TRIM and
SENSE(–) pins (Radj-down), the output voltage set point
(VO, adj) decreases (see Figure 19). The following equa-
tion determines the required external-resistor value to
obtain a percentage output voltage change of
%.
The test results for this conguration are displayed in
Figure 20. This gure applies to all output voltages.
With an external resistor connected between the TRIM
and SENSE(+) pins (Radj-up), the output voltage set
point (VO, adj) increases (see Figure 21).
The following equation determines the required exter-
nal-resistor value to obtain a percentage output voltage
change of
%.
The test results for this conguration are displayed in
Figure 22.
The voltage between the VO(+) and VO(–) terminals
must not exceed the minimum value of the output over-
voltage protection as indicated in the Feature Speci-
cations table. This limit includes any increase in voltage
due to remote-sense compensation and output voltage
set-point adjustment (trim). See Figure 18.
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim. Consult the factory if you
need to increase the output voltage more than the
above limitation.
The amount of power delivered by the module is
dened as the voltage at the output terminals multiplied
by the output current. When using remote sense and
trim, the output voltage of the module can be
increased, which at the same output current would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power.
8-748 (C).b
Figure 19. Circuit Conguration to Decrease
Output Voltage
VO(+)
SENSE(+)
SENSE(–)
VO(–)
VI(+)
VI(–)
IO
LOAD
CONTACT AND
DISTRIBUTION LOSSES
SUPPLY
II
CONTACT
RESISTANCE
Radj-down
205
%
----------
2.255
–
k
=
Radj-up
VO, nom 1
%
100
----------
+
() 1.225
–
()
1.225
%
()
------------------------------------------------------------------------- 205
2.255
–
k
=
VI(+)
VI(–)
ON/OFF
CASE
VO(+)
VO(–)
SENSE(+)
TRIM
SENSE(–)
Radj-down
RLOAD
相關PDF資料 |
PDF描述 |
|---|---|
| FW250B1 | DC-DC REG PWR SUPPLY MODULE |
| FW250C1 | DC-DC REG PWR SUPPLY MODULE |
| FW300C1 | DC-DC REG PWR SUPPLY MODULE |
| FW250G1 | DC-DC REG PWR SUPPLY MODULE |
| FW300G1 | DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FW300AF1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter |
| FW300-B | 制造商:Maxell 功能描述:Ear Bud Headphone With Microphone - With Apple Control - Blue |
| FW300B1 | 功能描述:CONVERTER DC/DC 12V 300W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW300 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| FW300C1 | 功能描述:CONVERTER DC/DC 15V 300W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW300 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| FW300D1 | 制造商:GE Energy (formerly Lineage Power) 功能描述:108545856 |
發布緊急采購，3分鐘左右您將得到回復。