- 您現在的位置：買賣IC網 > PDF目錄68996 > FW300G1 (LINEAGE POWER LLC) DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FW300G1 |
| 廠商： | LINEAGE POWER LLC |
| 元件分類： | 電源模塊 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 19/20頁 |
| 文件大?。?/td> | 570K |
| 代理商： | FW300G1 |
8
Lineage Power
Data Sheet
April 2008
dc-dc Converters; 36 to 75 Vdc Input, 2.5 Vdc Output; 125 W to 150 W
FW250G1 and FW300G1 Power Modules:
Test Congurations
8-203 (C).o
Note: Measure input reected-ripple current with a simulated source
inductance (LTEST) of 12 H. Capacitor CS offsets possible bat-
tery impedance. Measure current as shown above.
Figure 8. Input Reected-Ripple Test Setup
8-513 (C).m
Note: Use a 0.1 F ceramic capacitor and a 10 F aluminum or
tantalum capacitor. Scope measurement should be made
using a BNC socket. Position the load between 50 mm and
76 mm (2 in. and 3 in.) from the module.
Figure 9. Peak-to-Peak Output Noise Measurement
Test Setup
8-683 (C).f
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
Figure 10. Output Voltage and Efciency
Measurement Test Setup
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test conguration in Figure 8, a 100 F
electrolytic capacitor (ESR < 0.3
at 100 kHz)
mounted close to the power module helps ensure sta-
bility of the unit. For other highly inductive source
impedances, consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e.,
UL1950, CSA C22.2 No. 950-95, and VDE 0805
(EN60950, IEC950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module’s output to be considered meet-
ing the requirements of safety extra-low voltage
(SELV), all of the following must be true:
s
The input source is to be provided with reinforced
insulation from any hazardous voltages, including the
ac mains.
s
One VI pin and one VO pin are to be grounded or both
the input and output pins are to be kept oating.
s
The input pins of the module are not operator acces-
sible.
s
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module’s output.
Note: Do not ground either of the input pins of the
module without grounding one of the output pins.
This may allow a non-SELV voltage to appear
between the output pin and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 20 A normal-blow fuse in the ungrounded lead.
TO OSCILLOSCOPE
12 H
VI(+)
VI(–)
BATTERY
LTEST
Cs 220 F
ESR < 0.1
@ 20
°C, 100 kHz
100 F
ESR < 0.3
@ 100 kHz
VO(+)
VO(–)
1.0 F
RESISTIVE
LOAD
SCOPE
COPPER STRIP
10.0 F
VI(–)
VO(+)
SENSE(+)
SENSE(–)
VO(–)
VI(+)
IO
LOAD
CONTACT AND
DISTRIBUTION LOSSES
SUPPLY
II
CONTACT
RESISTANCE
η
VO +
() – VO –
()
[]IO
VI +
() – VI –
()
[]II
--------------------------------------------------
x 100
%
=
相關PDF資料 |
PDF描述 |
|---|---|
| FW300A1-A | 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE |
| FW300C1 | 1-OUTPUT 300 W DC-DC REG PWR SUPPLY MODULE |
| FW250C1 | 1-OUTPUT 250 W DC-DC REG PWR SUPPLY MODULE |
| FW300S10R01 | 1-OUTPUT 305.4 W DC-DC REG PWR SUPPLY MODULE |
| FXLP4555MPX | SPECIALTY ANALOG CIRCUIT, QCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FW300H1 | 功能描述:CONVERTER DC/DC 24V 300W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW300 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| FW300-P | 制造商:Maxell 功能描述:Ear Bud Headphone With Microphone - With Apple Control - Pink |
| FW300R1 | 功能描述:CONVERTER DC/DC 28V 300W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW300 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入（最?。?42V 電壓 - 輸入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出（最大）:* 電源（瓦） - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源（瓦特）- 最大:* |
| FW300S6R0 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter |
| FW3012-760 | 功能描述:插入式交流適配器 30 Watts 12V RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓（通道 1）:5 V 輸出電流（通道 1）:1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V |
發布緊急采購，3分鐘左右您將得到回復。