- 您現在的位置：買賣IC網 > PDF目錄382972 > FX489 (Electronic Theatre Controls, Inc.) GMSK Modem PDF資料下載
參數資料
| 型號： | FX489 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | GMSK Modem |
| 中文描述： | GMSK調制解調器 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 106K |
| 代理商： | FX489 |
6
Application Information ......
Rx Signal Path Description
The function of the Rx circuitry is to:
1. Set the incoming signal to a usable level.
2. Clean the signal by filtering.
3. Provide d.c. level thresholds for clock and data
extraction.
4. Provide clock timing information for data
extraction and external circuits.
5. Provide Rx data in a binary form.
6. Assess signal quality and provide Signal-to-Noise
information.
The output of the radio receiver's Frequency
Discriminator should be fed to the FX489's Rx Filter via
a suitable gain and d.c. level adjusting circuit. This gain
circuit can be built, with external components, around
the on-chip Rx Input Amplifier, with the gain set so that
the signal level at the Rx Feedback pin is nominally
1-volt peak-to-peak centred around V
when
receiving a continuous “1111000011110000 ..” data
pattern.
Positive going signal excursions at Rx Feedback
pin will produce a logic “0” at the Rx Data Output.
Negative going excursions will produce a logic “1.”
The received signal is fed through the lowpass Rx
Filter, which has a -3dB corner frequency of 0.56 times
the data bit-rate, before being applied to the Level
Measure and Clock and Data extraction blocks.
The Level Measuring block consists of two voltage
detectors. One of which measures the amplitude of the
‘positive’ parts of the received signal; The other
measures the amplitude of the ‘negative’ portions.
External capacitors are used by these detectors, via
the Doc 1/2 pins, to form voltage- ‘hold’ or ‘integrator’
circuits. Results of the two measurements are then
processed to establish the optimum d.c. level decision-
thresholds for the Clock and Data extraction,
depending upon the Rx signal amplitude, BT and any
d.c. offset present.
Rx Circuit Control Modes
The operating characteristics of the Rx Level
Measurement and Clock Extraction circuits are
controlled, as shown in Table 2, by logic level inputs
applied to the ‘PLLacq,’ ‘Rx Hold’ and ‘RxDCacq’ pins
to suit a particular application, or to cope with changing
reception conditions.
With reference to Figure 5, the Rx Mode Control
diagram. In general, a data transmission will begin with
a preamble of, for example, “1100110011001100,” to
allow the receive modem to establish timing- and level-
lock as quickly as possible. After the Rx carrier has
been detected, and during the time that the preamble
is expected, the ‘RxDCacq’ and ‘PLLacq’ inputs should
be switched from a logic “0 to 1” so that the Level
Measuring and Clock Extraction modes are operated
and sequenced as shown.
The ‘Rx Hold’ input should normally be held at a
logic “1” while data is being received, but may be
driven to a logic “0” to freeze the Level Measuring and
Clock Extraction circuits during a fade. If the fade lasts
for less than 200 bit periods, normal operation can be
resumed by returning the ‘Rx Hold’ input to a logic “1”
at the end of the fade. For longer fades, it may be
better to reset the Level Measuring circuits by placing
the ‘RxDCacq’ to a logic “1” for 10 to 20 bit periods.
‘Rx Hold’ has no effect on the Level Measuring
circuits while ‘RxDCacq’ is at a logic “1,” and has no
effect on the PLL while ‘PLLacq’ is at a logic “1.”
A logic “0” on ‘Rx Hold’ does not disable the ‘Rx
Clock’ output, and the Rx Data Extraction and S/N
Detector circuits will continue to operate.
PREAMBLE
DATA
’ACQUIRE’
Rx SIGNAL
INPUT
Rx CAR DET
(RSSI) INPUT
CLOCK
EXTRACTION
CCT MODE
’MEDIUM BW’
’NARROW BW’
30 BITS
’CLAMP’
’FAST PEAK
DETECT’
’AVERAGING PEAK
DETECT’
RxDCacq
PLLacq
Rx LEVEL
MEASURE
MODE
Fig.5 Rx Mode Control Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| FX489DW | GMSK Modem |
| FX489P | GMSK Modem |
| FX501 | High-Current Switching Applications |
| FX502 | High-Current Switching Applications |
| FX504 | High-Current Switching Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FX489DW | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GMSK Modem |
| FX489P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GMSK Modem |
| FX4A1-20P-1.27SV | 制造商:HRS 制造商全稱:HRS 功能描述:Stacking Height 5 to 11mm Half Pitch Connector |
| FX4A1-20P-1.27SV(71) | 功能描述:板對板與夾層連接器 20P STRT SMT HEADER NO LOC BOSS GLD PLT RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
| FX4A1-20P-1.27SV(99) | 功能描述:板對板與夾層連接器 20P STRT SMT HEADER NO LOC BOSS GLD PLT RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
發布緊急采購，3分鐘左右您將得到回復。