參數資料
型號: G525A1
廠商: Global Mixed-mode Technology Inc.
英文描述: USB High-Side Power Switch Advance Information
中文描述: 的USB高側電源開關進展信息
文件頁數: 6/8頁
文件大?。?/td> 243K
代理商: G525A1
Ver: 1.2
Nov 11, 2002
TEL: 886-3-5788833
http://www.gmt.com.tw
6
G525A
Global Mixed-mode Technology Inc.
from turning on until the die temperature drops to
125°C. Thermal shutdown circuit functions only when
the switch is enabled.
Undervoltage Lockout
UVLO (undervoltage lockout) prevents the output
MOSFET from turning on until IN (input voltage) ex-
ceeds 2.5V typically. After the switch turns on, if the
voltage drops below 2.3V typically, UVLO shuts off the
output MOSFET and signals the fault flag. UVLO de-
tection functions only when the switch is enabled.
Current Sensing and Limiting
The current limit threshold is preset internally. The
preset level prevents damage to the output MOSFET
and external load but allows a minimum current of
0.5A through the output MOSFET.
A current sense circuit senses the output current of
MOSFET switch. If output current exceeds the current
limit threshold, the output MOSFET switch is shut off
and a fault flag is pulled low. The reaction to an over-
current is measured with the following scenarios:
Switch Enabled into Heavy Load
If the switch is powered on or enabled into a heavy
load or short-circuit, the switch immediately goes into
a constant-current mode, reducing the output voltage.
The fault flag goes low until the load is reduced or
thermal shutdown occurs. See the "Enable into Short
Circuit" graph.
Heavy Load Applied to Enabled Switch
When a heavy load is applied, a large current may
flow from the switch. The current limit circuit may shut
the switch off briefly, then fold back into con-
stant-current mode. In that case, the fault flag falls
until the load is reduced. See the “Short Applied to
Output” graph and the "Ramped Load to Enable De-
vice" graph.
Fault Flag
FLG is a 2-channel, open-drain MOSFET output. The
fault-flag is active (low) for one or more of the follow-
ing conditions: current limiting, undervoltage, or ther-
mal shutdown. The flag output MOSFET is capable of
sinking a 10mA load to typically 100mV above ground.
Applications Information
Supply filtering
A 0.1F to 1F bypass capacitor from IN to GND, lo-
cated near the G525A, is strongly recommended to
control supply transients. Without a bypass capacitor,
an output short may cause sufficient ringing on the
input (from supply lead inductance) to damage internal
control circuitry.
Input transients must not exceed the absolute maxi-
mum supply voltage (VIN max = 6V) even for a short du-
ration.
Figure 1. Supply Bypassing
Figure 2. Soft Start
EN
FLG
GND
NC
OUT
IN
OUT
NC
G525A
3.0V to 5.5V
1
2
3
4
8
7
6
5
0.1 F to 1 F
EN
FLG
GND
NC
OUT
IN
OUT
NC
G525A
3.0V to 5.5V
1
2
3
4
8
7
6
5
0.1 F to 1 F
USB Host
GND
V
BUS
Cable
Bus Powered Hub
USB
Controller
EN
FLG
GND
NC
OUT
IN
OUT
NC
C
BULK
4.7
F
G525A
Cable
Downstream USB Device
Capacitive
Load
1
2
3
4
8
7
6
5
0.1 F
USB Host
GND
V
BUS
Cable
Bus Powered Hub
USB
Controller
EN
FLG
GND
NC
OUT
IN
OUT
NC
C
BULK
4.7
F
G525A
Cable
Downstream USB Device
Capacitive
Load
1
2
3
4
8
7
6
5
0.1 F
相關PDF資料
PDF描述
G525A2 USB High-Side Power Switch Advance Information
G528A USB High-Side Power Switch Advance Information
G528AP1U USB High-Side Power Switch Advance Information
G528AP1UF USB High-Side Power Switch Advance Information
G528P1U USB High-Side Power Switch Advance Information
相關代理商/技術參數
參數描述
G525A2 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:USB High-Side Power Switch Advance Information
G526 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual USB High-Side Power Switch
G526-1 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual USB High-Side Power Switch
G526-2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual USB High-Side Power Switch
G528 制造商:GMT 制造商全稱:Global Mixed-mode Technology Inc 功能描述:USB High-Side Power Switch Advance Information