- 您現在的位置：買賣IC網 > PDF目錄67610 > GB12232ASGAAMDA-V01 (Jewel Hill Electronic Co., Ltd.) SPECIFICATIONS FOR LCD MODULE PDF資料下載
參數資料
| 型號： | GB12232ASGAAMDA-V01 |
| 廠商： | Jewel Hill Electronic Co., Ltd. |
| 英文描述： | SPECIFICATIONS FOR LCD MODULE |
| 中文描述： | 規格液晶模塊 |
| 文件頁數： | 14/23頁 |
| 文件大小： | 363K |
| 代理商： | GB12232ASGAAMDA-V01 |
GB12232A
VER: 4.0
- 20 -
Issue date: 2006/08/01
JEWEL HILL ELECTRONIC CO.,LTD.
11.3 ELECTRO-STATIC DISCHARGE CONTROL
Since this module uses a CMOS LSI, the same careful attention should be paid for electrostatic
discharge as for an ordinary CMOS IC.
(1) Make certain that you are grounded when handing LCM.
(2) Before removing LCM from its packing case or incorporating it into a set, be sure the module
and your body have the same electric potential.
(3) When soldering the terminal of LCM, make certain the AC power source for the soldering iron
does not leak.
(4) When using an electric screwdriver to attach LCM, the screwdriver should be of ground
potentiality to minimize as much as possible any transmission of electromagnetic waves
produced sparks coming from the commutator of the motor.
(5) As far as possible, make the electric potential of your work clothes and that of the
workbenches to the ground potential.
(6) To reduce the generation of electro-static discharge, be careful that the air in the work is not
too dried. A relative humidity of 50%-60% is recommended.
11.4 PRECAUTIONS FOR OPERATION
(1) Viewing angle varies with the change of liquid crystal driving voltage (Vo). Adjust Vo to
show the best contrast.
(2) Driving the LCD in the voltage above the limit will shorten its lifetime.
(3) Response time is greatly delayed at temperature below the operating temperature range.
However, this does not mean the LCD will be out of the order. It will recover when it returns
to the specified temperature range.
(4) If the display area is pushed hard during operation, the display will become abnormal.
However, it will return to normal if it is turned off and then on.
(5) Condensation on terminals can cause an electrochemical reaction disrupting the terminal
circuit. Therefore, this product must be used and stored within the specified condition of
23±5°C, 45±20%RH.
(6) When turning the power on, input each signal after the positive/negative voltage becomes stable.
11.5 SAFETY
(1) It is recommended to crush damaged or unnecessary LCDs into pieces and wash them off
with solvents such as acetone and ethanol, which should later be burned.
(2) If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off
thoroughly with soap and water.
相關PDF資料 |
PDF描述 |
|---|---|
| GB12232ASGAAMDB-V01 | SPECIFICATIONS FOR LCD MODULE |
| GB12232ASGAAMLA-V01 | OSCILLATOR,40.000MHZ,HALF CAN TTL,70MA,5NS |
| GB12232ASGAAMLB-V01 | OSC,TTL,HALF SIZE,48.000MHZ, 70MA,5NS |
| GB12232ASGAAMUA-V01 | OSC,64.000MHZ,HALF CAN,TTL, 70MA,5NS |
| GB12232ASGAAMUB-V01 | CRYSTAL,3.579545MHZ,CSM-7,17PF HC49/US |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GB12232ASGAAMDB-V01 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB12232ASGAAMLA-V01 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB12232ASGAAMLB-V01 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB12232ASGAAMUA-V01 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
| GB12232ASGAAMUB-V01 | 制造商:JHE 制造商全稱:Jewel Hill Electronic 功能描述:SPECIFICATIONS FOR LCD MODULE |
發布緊急采購，3分鐘左右您將得到回復。