- 您現在的位置：買賣IC網 > PDF目錄384335 > GN8062 (PANASONIC CORP) GaAs IC PDF資料下載
參數資料
| 型號： | GN8062 |
| 廠商： | PANASONIC CORP |
| 元件分類： | 其它接口 |
| 英文描述： | GaAs IC |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 3/3頁 |
| 文件大?。?/td> | 55K |
| 代理商： | GN8062 |
GaAs MMICs
GN8062
I
Block Diagram
I
Caution for Handling
1) The recommended V
IN
voltage is 2.5 to 3V for [H] and
0 to 0.4V for [L].
2) Do not apply V
IN
while the power supply is OFF.
3) For the current source to be connected to the V
IP
pin,
use a Si bipolar transistor as shown in the circuit dia-
gram.
(Example: 2SD874)
To connect a resistor to the emitter or collector, use a
resistor of a few ohm. The use of higher resistor may
cause large change in the voltage at the V
IP
pin, and
may make the output waveform distortion. (See the pulse
output current control example).
To use another current control circuit, set so that the V
IP
pin voltage becomes around 2V.
4) When mounting, minimize the connection distance be-
tween the semiconductor laser and IC, and use the chip
parts (C, R) of less parasitic effects.
5) Attention to damage by the power surge (see the ex-
ample connection of the pin protection circuit).
During handling, take care to ground the human body
and solder iron tip.
6) When the power supply is turned ON and OFF, set the
current value of the current source connected to the V
IP
pin to zero. This is important to prevent the large cur-
rent flow through the semiconductor laser during power
ON/OFF.
When the power supply is ON, be sure to turn ON V
DD
,
after V
SS
is completely equal to – 5V. When the power
supply is OFF, be sure to turn OFF V
SS
, after V
DD
is
completely 0V.
7) Pay attention to release the heat.
Example of pulse output current control circuit
Connection example of pin protection circuit
V
IN
GND
NC
NC
OUT
OUT
1
2
3
4
8
7
6
5
V
SS
V
SS
V
SS
V
SS
V
SS
V
IN
V
DD
V
IP
V
DD
V
DD
V
IP
+5V
LASER DIODE
OUTSIDE GN8062
INSIDE GN8062
from CONTROL
CIRCUIT
–5.0V
200
to 2k
50
5.0V
GN8062
MA3068(V
Z
=6.8V,Cd=85pF,R
Z
=6
)
GND
NC
NC
OUT
V
SS
V
IN
V
DD
V
IP
GND
NC
I
B
V
EE
=–5 to 0V
I COLLECTOR
NC
OUT
V
SS
V
IN
V
DD
V
IP
5
0.22
m
F
–
GN8062
相關PDF資料 |
PDF描述 |
|---|---|
| GP-485 | Aluminum Electrolytic Radial Leaded Low Profile Capacitor; Capacitance: 220uF; Voltage: 63V; Case Size: 12.5x12.5 mm; Packaging: Bulk |
| GP-486 | Mini-Triggered Spark Gaps and Transformers |
| GP-488 | Aluminum Electrolytic Radial Leaded Low Profile Capacitor; Capacitance: 680uF; Voltage: 63V; Case Size: 25x12.5 mm; Packaging: Bulk |
| GP-489 | Mini-Triggered Spark Gaps and Transformers |
| GP-90 | Triggered Spark Gaps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GN809 | 制造商:GTM 制造商全稱:GTM 功能描述:UPROCESSOR SUPERVISORY |
| GN84134120 | 制造商:Schneider Electric 功能描述:RELAY |
| GN84137860 | 制造商:CROUZET 功能描述: |
| GN-87 | 功能描述:IC RECEIVER GPS/GNSS 24LCC 制造商:volgen america/kaga electronics usa 系列:87 包裝:剪切帶（CT） 零件狀態:在售 頻率:1.575GHz 靈敏度:-161dBm 數據速率（最大值）:- 調制或協議:Galileo，GLONASS，GPS 應用:通用 電流 - 接收:72mA ~ 84mA 數據接口:I2C，UART 存儲容量:- 天線連接器:堡形 特性:- 電壓 - 電源:3.3V 工作溫度:-40°C ~ 85°C 封裝/外殼:24-SMD 模塊 供應商器件封裝:模塊 標準包裝:1 |
| GN-9070224 | 制造商:Alarm Suppliers 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。