- 您現在的位置：買賣IC網 > PDF目錄370379 > GS-R51X1XS 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C PDF資料下載
參數資料
| 型號： | GS-R51X1XS |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 500kHz and 1MHz High Efficiency 1.5A Switching Regulators; Package: SO; No of Pins: 8; Temperature Range: -40?°C to 85?°C |
| 中文描述： | 射頻放大器 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 434K |
| 代理商： | GS-R51X1XS |
5/8
USER NOTES
Input Voltage
The recommended operating maximum DC input
voltage is 40V inclusive of the ripple voltage. The
use of an external low ESR, high ripple current
capacitor located as close the module as possible
is recommended; suggested value is 100
μ
F/50V.
Soft-start
To avoid heavy inrush current the output voltage
rise time is typically 10ms in any condition of load.
Power Fail-Reset Circuit
The module include a voltage sensing circuit that
may be used to generate a power-on/power-off
reset signal for a microprocessor system.
The circuit sense the input supply voltage and the
output generated voltage Vo1 (+5V) and will gener-
ate the required reset signal only when both the
sensed voltages have reached the required value
for correct system operation.
When both the supply voltage and the regulated
voltage are in the correct range the output Reset
signal is generated after a delay time t
DR
of 100ms
typical.
A latch assures that if a spike is present on the
sensed voltage the delay time circuit discharges
completely before initialization of a new reset cycle.
Reset output has internal pull-up resistor of
10kOhm connected to Vo +5V pin.
Maximum sink output current is 20mA at
V
RESET(sat)
= 200mV.
Fig. 1 and fig. 2 show reset waveforms.
Power Fail Programmable Input
This pin is internally connected via a divider to the
+Vin pin for Power Fail function.
The factory setting is for a value of 11V with 1V
hysteresis.
It is possible to program a different value of Power
Fail threshold by connecting a resistor (Rpf) be-
tween pin 3 (Power Fail Input) and pin 1 (GND
Input). The value of Rpf must be calculated accord-
ing to the following formula:
R
pf
=
5.1
V
pf
34
=
(
k
)
0.191
where Vpf is the desired value of Power Fail thresh-
old voltage.
Exampe: Vpf = 24V (must not be lower than 12V):
R
pf
=
5.1
24
5.1
34
=
14k
0.191
Figure 1 - Reset and Power Fail waveforms.
GS-R51212S/GS-R51515S
相關PDF資料 |
PDF描述 |
|---|---|
| GS-T25-0500 | Analog IC |
| GS-T27-0600 | Analog IC |
| GS1140-1 | |
| GS1140-2 | |
| GS1140-3 | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GSR53 | 制造商:EUROQUARTZ 制造商全稱:EUROQUARTZ limited 功能描述:5 x 3.2 x 1.2mm SMD Sine Wave VCXO |
| GSR57 | 制造商:EUROQUARTZ 制造商全稱:EUROQUARTZ limited 功能描述:7 x 5 x1.8mm SMD Sine Wave VCXO |
| GSR5-V | 制造商:Ferraz Shawmut 功能描述: |
| GSR6.34F130QP | 功能描述:觸覺開關 SEALED 6.34MM PC PIN RoHS:否 制造商:C&K Components 工作力:2 N 執行器:Round 電流額定值:50 mA 電壓額定值 DC:32 V 電壓額定值 AC: 功率額定值:1 VA 接地端子:Yes 觸點形式:SPST-NO 開關功能: 安裝風格:SMD/SMT 安裝方向:Right 晶體管管座高度: 顏色: 照明:Not Illuminated 照明顏色: 封裝: |
| GSR6.34F130RP | 制造商:E-Switch Inc 功能描述:SWITCH TACTILE |
發布緊急采購，3分鐘左右您將得到回復。