- 您現在的位置：買賣IC網 > PDF目錄385344 > GS9020ACTVE3 (Gennum Corporation) GENLINX -TM II GS9020A Serial Digital Video Input Processor PDF資料下載
參數資料
| 型號： | GS9020ACTVE3 |
| 廠商： | Gennum Corporation |
| 英文描述： | GENLINX -TM II GS9020A Serial Digital Video Input Processor |
| 中文描述： | GENLINX -商標二GS9020A串行數字視頻輸入處理器 |
| 文件頁數： | 9/31頁 |
| 文件大小： | 258K |
| 代理商： | GS9020ACTVE3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
19922 - 3
9 of 31
G
The serial data output circuits are shown in Figure 6. The
serial data outputs are designed to drive 50-75
controlled
impedance traces and can be easily connected to the
GS9028 cable driver as shown in Figure 7 and Figure 18.
Note that to output proper PECL signal levels, a resistor
must be connected between the two serial data outputs.
1.4 Automatic Standard Detection
The device automatically detects the incoming video
standard. The detected standard is encoded on the
STD[3:0] pins and the HOSTIF read table bits as shown in
Table 1 and Table 3.
Noise immunity is included to ensure that momentary signal
corruption does not affect the automatic standards
detection function. This built in noise immunity results in
delayed detection time during power up and when
switching between standards. Delays range from as little as
eight lines when switching between component standards
to as much as four frames when switching between PAL
and NTSC standards. If this delay is intolerable, the user
can manually set the standard through the HOSTIF write
table. To set the standard manually, the STD_SEL bit must
be set HIGH and the S bit and STD[3:0] pins/HOSTIF bits
set accordingly. The default standard upon reset of the chip
is NTSC 4:2:2 component (13.5MHz Y sampling).
The S bit, used for single link data standards only, is
encoded in the TRSID word and indicates if the data is in
RGB or YC
R
C
B
format as per SMPTE RP174. In automatic
standard detection mode, the S bit can be read from the
HOSTIF read table. In manual mode, the S bit must be set
in the HOSTIF write table.
1.5 Parallel Clock Output
The PCLKOUT pin provides the output parallel clock. All
synchronous I/O are timed relative to PCLKOUT. The
following listing shows which I/O's are synchronous and
which are not. Timing for synchronous outputs is shown in
Figure 3. Timing for synchronous inputs is shown in
Figure 2.
PIN
LOGIC OPR
HOST BIT
STD_SEL
STD[3:0]
STD[3:0]
S
TABLE 1
STANDARD NAME
STD[3:0]
NTSC 4:2:2 Component with 13.5MHz Y sampling
0000
NTSC Composite
0001
NTSC 4:2:2 16x9 Widescreen with 18MHz Y
sampling
0010
NTSC 4:4:4:4 Single Link with 13.5MHz Y sampling
0011
PAL 4:2:2 Component with 13.5MHz Y sampling
0100
PAL Composite
0101
PAL 4:2:2 16x9 Widescreen with 18MHz Y sampling
0110
PAL 4:4:4:4 Single Link with 13.5MHz Y sampling
0111
PIN
LOGIC OPR
HOST BIT
PCLKOUT
SYNCHRONOUS
ASYNCHRONOUS
FL[4:0]
P[7:5]
S[1:0]
SCL/P4
FIFO_RESET
INTERRUPT
DOUT[9:0]
SDA/P3
F[2:0]
A[2:0]/P[2:0]
V
R/W
H
A/D
ANC_DATA
CS
BLANK_EN
FLAG_MAP
F_R/W
RESET
NO_EDH
CRC_MODE
STD[3:0]
VBLANKS/L
TRS_ERROR
HOSTIF_MODE
FIFOE/S
FLYWDIS
BYPASS_EDH
SDO_MODE
ANC_CHKSM
CLIP_TRS
相關PDF資料 |
PDF描述 |
|---|---|
| GS9021A | GENLINX -TM II GS9021A EDH Coprocessor |
| GS9021ACFU | GENLINX -TM II GS9021A EDH Coprocessor |
| GS9022-CPJ | Digital Video Serializer |
| GS9022 | Digital Video Serializer |
| GS9022-CTJ | Digital Video Serializer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS9020-CFV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial Digital Video Input Processor |
| GS9020-CTV | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Serial Digital Video Input Processor |
| GS9021 | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:EDH Coprocessor |
| GS9021A | 制造商:GENNUM 制造商全稱:GENNUM 功能描述:GENLINX -TM II GS9021A EDH Coprocessor |
| GS9021ACFU | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。