2
FN2856.7
October 24, 2013
Absolute Maximum Ratings
Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . .40V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24V
Digital Input Voltage (Sample and Hold Pin) . . . . . . . . . . +8V, -15V
Output Current . . . . . . . . . . . . . . . . . . . . . . . .Short Circuit Protected
Operating Conditions
Temperature Range
HA-2420-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55°C to +125°C
Supply Voltage Range (Typical) . . . . . . . . . . . . . . . . ±12V to ±15V
Thermal Resistance (Typical, Note 1)
θJA (°C/W) θJC (°C/W)
CERDIP Package. . . . . . . . . . . . . . . . .
75
20
Maximum Junction Temperature (Ceramic Packages) . . . . . . +175°C
Maximum Storage Temperature Range . . . . . . . . -65°C to +150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications
Test Conditions (Unless Otherwise Specified) VSUPPLY = ±15.0V; CH = 1000pF; Digital Input: VIL =+0.8V
(Sample), VIH = +2.0V (Hold), Unity Gain Configuration (Output tied to Negative Input)
PARAMETER
TEST
CONDITIONS
TEMP.
(°C)
MIN
TYP
MAX
UNITS
INPUT CHARACTERISTICS
Input Voltage Range
Full
±
10
-
V
Offset Voltage
25
-
2
4
mV
Full
-
3
6
mV
Bias Current
25
-
40
200
nA
Full
-
400
nA
Offset Current
25
-
10
50
nA
Full
-
100
nA
Input Resistance
25
5
10
-
M
Ω
Common Mode Range
Full
±
10
-
V
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
RL = 2kΩ , VO = 20VP-P
Full
25
50
-
kV/V
Common Mode Rejection
VCM = ±10V
Full
80
90
-
dB
Hold Mode Feedthrough Attenuation (Note 2)
fIN ≤ 100kHz
Full
-
-76
-
dB
Gain Bandwidth Product (Note 2)
25
-
2.5
-
MHz
OUTPUT CHARACTERISTICS
Output Voltage Swing
RL = 2kΩ
Full
±
10
-
V
Output Current
25
-
mA
Full Power Bandwidth (Note 2)
VO = 20VP-P
25
-
100
-
kHz
Output Resistance
DC
25
-
0.15
-
Ω
TRANSIENT RESPONSE
Rise Time (Note 2)
VO = 200mVP-P
25
-
75
100
ns
Overshoot (Note 2)
VO = 200mVP-P
25
-
25
40
%
Slew Rate (Note 2)
VO = 10VP-P
25
3.5
5
-
V/s
DIGITAL INPUT CHARACTERISTICS
Digital Input Current
VIN = 0V
Full
-
-0.8
mA
VIN = 5V
Full
-
20
A
HA-2420