![](http://datasheet.mmic.net.cn/Intersil/HA9P4905-5_datasheet_104718/HA9P4905-5_2.png)
2
Absolute Maximum Ratings
Thermal Information
Supply Voltage (Between V+ and V- Terminals) . . . . . . . . . . . . . . . . . 33V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15V
Voltage Between VLOGIC+ and VLOGIC- . . . . . . . . . . . . . . . . . . . . . . .18V
Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Power Dissipation (Notes 1, 2)
Operating Conditions
Temperature Range
HA-4900-2, HA-4902-2 . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
HA-4905-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0oC to 75oC
Thermal Resistance (Typical, Note 3)
θ
JA (
oC/W)
θ
JC (
oC/W)
CERDIP Package . . . . . . . . . . . . . . . . . . . .
85
25
PDIP Package . . . . . . . . . . . . . . . . . . . . . . .
90
N/A
SOIC Package . . . . . . . . . . . . . . . . . . . . . . .
100
N/A
Maximum Junction Temperature (Ceramic Package) . . . . . . . . . . . . 175oC
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
Die Characteristics
Back Side Potential. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V-
Number of Transistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Die Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 mils x 105 mils
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or
any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. Maximum power dissipation, including output load, must be designed to maintain the junction temperature below 175oC for ceramic packages, and below
150oC for plastic packages.
2. Total Power Dissipation (T.P.D.) is the sum of individual dissipation contributions of V+, V- and VLOGIC shown in curves of Power Dissipation vs Supply
Voltages (see Performance Curves). The calculated T.P.D. is then located on the graph of Maximum Allowable Package Dissipation vs Ambient Temperature
to determine ambient temperature operating limits imposed by the calculated T.P.D. (See Performance Curves). For instance, the combination of +15V, -15V,
+5V, 0V (V+, V-, VLOGIC+, VLOGIC-) gives a T.P.D. of 350mW, the combination +15V, -15V, +15V, 0V gives a T.P.D. of 450mW.
3.
θ
JA is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
VSUPPLY = ±15V, VLOGIC+ = 5V, VLOGIC- = GND
PARAMETER
TEMP
(oC)
HA-4900-2
-55oC to 125oC
HA-4902-2
-55oC to 125oC
HA-4905-5
0oC to 75oC
UNITS
MIN
TYP
MAX
MIN
TYP
MAX
MIN
TYP
MAX
INPUT CHARACTERISTICS
Offset Voltage (Note 4)
25
-
2
3
-
2
5
-
4
7.5
mV
Full
-
4
-
8
-
10
mV
Offset Current
25
-
10
25
-
10
35
-
25
50
nA
Full
--
35
--
45
-
70
nA
Bias Current (Note 5)
25
-
50
75
-
50
150
-
100
150
nA
Full
-
150
-
200
-
300
nA
Input Sensitivity (Note 6)
25
-
VIO +
0.3
--
VIO +
0.5
--
VIO +
0.5
mV
Full
-
VIO +
0.4
--
VIO +
0.6
--
VIO +
0.7
mV
Common Mode Range
Full
V-
-
(V+) -
2.4
V-
-
(V+) -
2.6
V-
-
(V+) -
2.4
V
Differential Input Resistance
25
-
250
-
250
-
250
-
M
Ω
TRANSFER CHARACTERISTICS
Large Signal Voltage Gain
25
-
400
-
400
-
400
-
kV/V
Response Time (tPD(0))
(Note 7)
25
-
130
200
-
130
200
-
130
200
ns
Response Time (tPD(1))
(Note 7)
25
-
180
215
-
180
215
-
180
215
ns
OUTPUT CHARACTERISTICS
Output Voltage Level
HA-4900, HA-4902, HA-4905