- 您現在的位置：買賣IC網 > PDF目錄371767 > HA5023IB (HARRIS SEMICONDUCTOR) COVER AND RETAINER, 8WAY; For use with:J Connectors; Material:High Impact Thermoplastic; Connector shell size:8; Colour:Grey; Connector type:Backshell; Ways, No. of:8 RoHS Compliant: Yes PDF資料下載
參數資料
| 型號： | HA5023IB |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | COVER AND RETAINER, 8WAY; For use with:J Connectors; Material:High Impact Thermoplastic; Connector shell size:8; Colour:Grey; Connector type:Backshell; Ways, No. of:8 RoHS Compliant: Yes |
| 中文描述： | VIDEO AMPLIFIER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 16/19頁 |
| 文件大小： | 813K |
| 代理商： | HA5023IB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁
DESIGN INFORMATION
(Continued)
The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application
and design information only. No guarantee is implied.
16
HA5023
Application Information
Optimum Feedback Resistor
The plots of inverting and non-inverting frequency response,
see Figure 1 and Figure 2 in the typical performance section,
illustrate the performance of the HA5023 in various closed
loop gain configurations. Although the bandwidth depen-
dency on closed loop gain isn’t as severe as that of a voltage
feedback amplifier, there can be an appreciable decrease in
bandwidth at higher gains. This decrease may be minimized
by taking advantage of the current feedback amplifier’s
unique relationship between bandwidth and R
F
. All current
feedback amplifiers require a feedback resistor, even for
unity gain applications, and R
F
, in conjunction with the inter-
nal compensation capacitor, sets the dominant pole of the
frequency response. Thus, the amplifier’s bandwidth is
inversely proportional to R
F
. The HA5023 design is opti-
mized for a 1000
R
F
at a gain of +1. Decreasing R
F
in a
unity gain application decreases stability, resulting in exces-
sive peaking and overshoot. At higher gains the amplifier is
more stable, so R
F
can be decreased in a trade-off of stabil-
ity for bandwidth.
The table below lists recommended R
F
values for various
gains, and the expected bandwidth.
PC Board Layout
The frequency response of this amplifier depends greatly on
the amount of care taken in designing the PC board. The
use of low inductance components such as chip resistors
and chip capacitors is strongly recommended. If leaded
components are used the leads must be kept short espe-
cially for the power supply decoupling components and
those components connected to the inverting input.
Attention must be given to decoupling the power supplies. A
large value (10
μ
F) tantalum or electrolytic capacitor in paral-
lel with a small value (0.1
μ
F) chip capacitor works well in
most cases.
A ground plane is strongly recommended to control noise.
Care must also be taken to minimize the capacitance to
ground seen by the amplifier’s inverting input (-IN). The
larger this capacitance, the worse the gain peaking, resulting
in pulse overshoot and possible instability. It is recom-
mended that the ground plane be removed under traces
connected to -IN, and that connections to -IN be kept as
short as possible to minimize the capacitance from this node
to ground.
Driving Capacitive Loads
Capacitive loads will degrade the amplifier’s phase margin
resulting in frequency response peaking and possible oscilla-
tions. In most cases the oscillation can be avoided by placing
an isolation resistor (R) in series with the output as shown in
Figure 34.
FIGURE 34. PLACEMENT OF THE OUTPUT ISOLATION
RESISTOR, R
The selection criteria for the isolation resistor is highly
dependent on the load, but 27
has been determined to be
a good starting value.
Power Dissipation Considerations
Due to the high supply current inherent in dual amplifiers, care
must be taken to insure that the maximum junction tempera-
ture (T
J
,
see Absolute Maximum Ratings) is not exceeded.
Figure 35 shows the maximum ambient temperature versus
supply voltage for the available package styles. It is recom-
mended that thermal calculations, which take into account
output power, be performed by the designer.
FIGURE 35. MAXIMUM OPERATING AMBIENT TEMPERATURE
vs SUPPLY VOLTAGE
GAIN
(A
CL
)
-1
R
F
(
)
750
BANDWIDTH
(MHz)
100
+1
1000
125
+2
681
95
+5
1000
52
+10
383
65
-10
750
22
V
IN
V
OUT
C
L
R
T
+
-
R
I
R
F
R
5
7
9
11
13
15
165
155
145
135
SUPPLY VOLTAGE (V)
CERDIP
M
o
C
125
相關PDF資料 |
PDF描述 |
|---|---|
| HA5023EVAL | Dual 125MHz Video Current Feedback Amplifier |
| HA5024 | Quad 125MHz Video Current Feedback Amplifier with Disable |
| HA5024IB | Quad 125MHz Video Current Feedback Amplifier with Disable |
| HA5024IP | Quad 125MHz Video Current Feedback Amplifier with Disable |
| HA5024EVAL | Quad 125MHz Video Current Feedback Amplifier with Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HA5023IB96 | 功能描述:IC OPAMP DUAL 125MHZ VIDEO 8SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| HA5023IBZ | 功能描述:運算放大器 - 運放 W/ANNEAL OPAMP 2X 12 5MHZ VID IND RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| HA5023IBZ96 | 功能描述:視頻放大器 W/ANNEAL OPAMP 2X 12 5MHZ VID IND RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| HA5023IP | 功能描述:IC OPAMP DUAL 125MHZ VIDEO 8-DIP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| HA5023IPZ | 功能描述:視頻放大器 W/ANNEAL OPAMP 2X 12 5MHZ CFB IND RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。