3
FN2845.12
May 21, 2013
Absolute Maximum Ratings (Note 3) Thermal Information
Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±VSUPPLY
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10V
Output Current . . . . . . . . . . . . . . . . . . . . . . . Short Circuit Protected
Operating Conditions
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +75°C
Thermal Resistance (Typical, Note
4)θJA (°C/W) θJC (°C/W)
PDIP Package* . . . . . . . . . . . . . . . . . .
120
N/A
SOIC Package . . . . . . . . . . . . . . . . . . .
165
N/A
Maximum Junction Temperature (Plastic Packages, Note
3) . . +150°C
Maximum Storage Temperature Range . . . . . . . . -65°C to +150°C
*Pb-free PDIPs can be used for through hole wave solder process-
ing only. They are not intended for use in Reflow solder processing
applications
Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
3. Maximum power dissipation, including output load, must be designed to maintain junction temperature below +150°C for plastic packages.
4.
θ
JA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details. Electrical Specifications
VSUPPLY = ±15V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤ 10pF,
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP.
(°C)
MIN
TYP
MAX
UNITS
INPUT CHARACTERISTICS
Input Offset Voltage (Notes
6, 17)25
-
2
8
mV
Full
-
10
mV
Average Input Offset Voltage Drift
Full
-
10
-
V/°C
VIO Common Mode Rejection Ratio (Note 17) VCM = ±10V
25
60
-
dB
Full
50
-
dB
VIO Power Supply Rejection Ratio (Note 17) ±4.5V
≤ VS ≤ ±18V
25
64
-
dB
Full
60
-
dB
Non-Inverting Input (+IN) Current (Note
17 )25
-
3
8
A
Full
-
20
A
+IN Common Mode Rejection
VCM = ±10V
25
-
0.1
A/V
Full
-
0.5
A/V
+IN Power Supply Rejection
±4.5V
≤ VS ≤ ±18V
25
-
0.06
A/V
Full
-
0.2
A/V
Inverting Input (-IN) Current (Note
17)25
-
12
20
A
Full
-
25
50
A
-IN Common Mode Rejection
VCM = ±10V
25
-
0.4
A/V
Full
-
0.5
A/V
-IN Power Supply Rejection
±4.5V
≤ VS ≤ ±18V
25
-
0.2
A/V
Full
-
0.5
A/V
TRANSFER CHARACTERISTICS
25
3500
-
V/mA
Full
1000
-
V/mA
Open Loop DC Voltage Gain (Note
12)RL = 400Ω,
VOUT = ±10V
25
70
-
dB
Full
65
-
dB
Open Loop DC Voltage Gain
RL = 100Ω,
VOUT = ±2.5V
25
60
-
dB
Full
55
-
dB
HA-5020