- 您現在的位置：買賣IC網 > PDF目錄371775 > HC55151 (Intersil Corporation) Low Power Universal SLIC Family PDF資料下載
參數資料
| 型號： | HC55151 |
| 廠商： | Intersil Corporation |
| 英文描述： | Low Power Universal SLIC Family |
| 中文描述： | 低功耗通用用戶接口家庭 |
| 文件頁數： | 19/35頁 |
| 文件大小： | 382K |
| 代理商： | HC55151 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
4-19
Digital Logic Inputs
Table 1 is the logic truth table for the 3V to 5V logic input
pins. A combination of the control pins C3, C2 and C1 select
1 of the possible 6 operating states. The 8th state listed is
Thermal Shutdown. Thermal Shutdown protection is invoked
if a fault condition on the tip or ring causes the junction
temperature of the die to exceed 175
o
C. A description of
each operating state and the control logic follows:
Open Circuit State (C3 = 0, C2 = 0, C1 = 0)
In this state, the tip and ring outputs are in a high impedance
condition (>1M
). No supervisory functions are available
and SHD and GKD outputs are at a TTL high level.
4-wire loopback testing can be performed in this state. With
the PTG pin floating, the signal on the V
TX
output is 180
o
out
of phase and approximately 2 times the V
RX
input signal. If
the PTG pin is grounded, then the amplitude will be
approximately the same as its input and 180
o
out of phase.
Ringing State (C3 = 0, C2 = 0, C1 = 1)
In this state, the output of the ring relay driver pin (RRLY)
goes low (energizing the ring relay to connect the ringing
signal to the phone) if either of the following two conditions
are satisfied:
(1) The RSYNC_REV pin is grounded through a resistor -
This connection enables the RRLY pin to go low the instant
the ringing state is invoked, without any regard for the ringing
voltage (90V
RMS
-120V
RMS
) across the relay contacts. The
resistor (34.8k
to 70k
) is required to limit the current into
the RSYNC_REV pin.
(2) A ring sync pulse is applied to the RSYNC_REV pin -
This connection enables the RRLY pin to go low at the
command of a ring sync pulse. A ring sync pulse should go
low at zero
voltage
crossing of the ring signal. This pulse
should have a rise and fall time <400
μ
s and a minimum
pulse width of 2ms.
Zero ring
current
detection is performed automatically
inside the SLIC. This feature de-energizes the ring relay
slightly before zero current occurs to partially compensate
for the delay in the opening of the relay.
The SHD output will go low when the subscriber goes off
hook. Once SHD is activated, an internal latch will prohibit
the re-ringing of the line until the ringing code is removed
and then reapplied.
The state prior to ringing the phone, can not be the Reverse
Active State. In the reverse active state the polarity of the
voltage on the CRT_REV_LVM capacitor, will make it appear
as if the subscriber is off hook. This subsequently will
activate an internal latch prohibiting the ringing of the line.
TABLE 1. DETECTOR STATES
STATE
C3
C2
C1
SLIC OPERATING STATE
ACTIVE DETECTOR
OUTPUT
SHD
GKD_ LVM
0
0
0
0
Open Circuit State
4 wire loopback test capability
HIGH
HIGH
1
0
0
1
Ringing State
(Previous State cannot be Reverse
Active State)
Ring Trip Detector
HIGH
2
0
1
0
Forward Active State
Loop Current Detector
Ground Key Detector
3
0
1
1
Test Active State
Requires previous state to be in the
Forward Active state to determine the
On hook or Off hook status of the line.
On Hook
Loopback Detector
LOW
Ground Key Detector
HIGH
Off Hook
Loop Current Detector
LOW
Line Voltage Detector
4
1
0
0
Tip Open - Ground Start State
Ground Key Detector
5
1
0
1
Reserved
Reserved
N/A
N/A
6
1
1
0
Reverse Active State
Loop Current Detector
Ground Key Detector
7
1
1
1
Test Reversal Active State
Requires previous state to be in the
ReverseActivestatetodeterminethe
On hook or Off hook status of the line.
On Hook
Loop Current Detector
HIGH
Off Hook
Loop Current Detector
LOW
Line Voltage Detector
8
X
X
X
Thermal Shutdown
LOW
LOW
HC55120, HC55121, HC55130, HC55131, HC55140, HC55141, HC55142, HC55143, HC55150, HC55151
相關PDF資料 |
PDF描述 |
|---|---|
| HC55120 | IC-VLTG REG POS 10V 1A |
| HC55120CB | Voltage Regulator IC; Output Current:2A; Output Voltage:5V; Package/Case:3-TO3P; Output Voltage Max:5.1V; Output Voltage Min:4.9V |
| HC55120CM | IC-VLTG REG POS 12V-2A |
| HC55121IM | TRANSISTOR,BJT,NPN,70V V(BR)CEO,1.5A I(C),TO-39 |
| HC55130IB | IC-VLTG REG +6V TO220 ISO |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC55151CM | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power Universal SLIC Family |
| HC5515CM | 制造商:Rochester Electronics LLC 功能描述:CO/PABX SLIC,53DB LONG BAL,28PLCC,COMMER - Bulk |
| HC5515CMZ | 功能描述:電信線路管理 IC CO/PABX SLIC 53DB LONG BAL 28PLCC COME RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| HC5515CP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC5515IM | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。