- 您現在的位置：買賣IC網 > PDF目錄371775 > HC55182DIM (HARRIS SEMICONDUCTOR) Extended Reach Ringing SLIC Family PDF資料下載
參數資料
| 型號： | HC55182DIM |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 模擬傳輸電路 |
| 英文描述： | Extended Reach Ringing SLIC Family |
| 中文描述： | TELECOM-SLIC, PQCC28 |
| 文件頁數： | 14/17頁 |
| 文件大?。?/td> | 168K |
| 代理商： | HC55182DIM |
4-14
Tip Open
Overview
The tip open mode (110) is intended for compatibility for
PBX type interfaces. Used during idle line conditions, the
device does not provide transmission. Loop supervision is
provided by either the switch hook detector (E0 = 1) or the
ground key detector (E0 = 0). The ground key detector will
be used in most applications. The device may be operated
from either high or low battery.
Functionality
During tip open operation, the Tip switch is disabled and the
Ring switch is enabled. The minimum Tip impedance is
30k
. The only active path through the device will be the
Ring switch.
In keeping with the MTU characteristics of the device, Ring
will not exceed -56V when operating from the high battery.
Though MTU does not apply to tip open, safety requirements
are satisfied.
Power Denial
Overview
The power denial mode (111) will shutdown the entire device
except for the logic interface. Loop supervision is not
provided. This mode may be used as a sleep mode or to
shut down in the presence of a persistent thermal alarm.
Switching between high and low battery will have no effect
during power denial.
Functionality
During power denial, both the Tip and Ring amplifiers are
disabled, representing high impedances. The voltages at
both outputs are near ground.
Thermal Shutdown
In the event the safe die temperature is exceeded, the ALM
output will go low and DET will go high and the part will
automatically shut down. When the device cools, ALM will
go high and DET will reflect the loop status. If the thermal
fault persists, ALM will go low again and the part will shut
down. Programming power denial will permanently
shutdown the device and stop the self cooling cycling.
Battery Switching
Overview
The integrated battery switch selects between the high
battery and low battery. The battery switch is controlled
with the logic input BSEL. When BSEL is a logic high, the
high battery is selected and when a logic low, the low
battery is selected. All operating modes of the device will
operate from high or low battery except forward loop back.
Functionality
The logic control is independent of the operating mode
decode. Independent logic control provides the most
flexibility and will support all application configurations.
When changing device operating states, battery switching
should occur simultaneously with or prior to changing the
operating mode. In most cases, this will minimize overall
power dissipation and prevent glitches on the DET output.
The only external component required to support the battery
switch is a diode in series with the V
BH
supply lead. In the
event that high battery is removed, the diode allows the
device to transition to low battery operation.
Low Battery Operation
All off hook operating conditions should use the low battery.
The prime benefit will be reduced power dissipation. The
typical low battery for the device is -24V. However this may
be increased to support longer loop lengths or high loop
current requirements. Standby conditions may also operate
from the low battery if MTU compliance is not required,
further reducing standby power dissipation.
High Battery Operation
Other than ringing, the high battery should be used for
standby conditions which must provide MTU compliance.
During standby operation the power consumption is typically
85mW with -100V battery. If ringing requirements do not
require full 100V operation, then a lower battery will result in
lower standby power.
High Voltage Decoupling
The 100V rating of the device will require a capacitor of
higher voltage rating for decoupling. Suggested decoupling
values for all device pins are 0.1
μ
F. Standard surface mount
ceramic capacitors are rated at 100V. For applications driven
at low cost and small size, the decoupling scheme shown
below could be implemented.
It is important to place the external diode between the VBH
pin and the decoupling capacitor. Attaching the decoupling
capacitor directly to the VBH pin will degrade the reliability of
the device. Refer to Figure 12 for the proper arrangement.
This applies to both single and stacked and decoupling
arrangements.
If VBL and VBH are tied together to override the battery
switch function, then the external diode is not needed and
the decoupling may be attached directly to VBH.
FIGURE 12. ALTERNATE DECOUPLING SCHEME
VBH
VBL
HC5518X
0.22
μ
0.22
μ
HC55185
相關PDF資料 |
PDF描述 |
|---|---|
| HC55184ECM | Extended Reach Ringing SLIC Family |
| HC55185 | VoIP Ringing SLIC Family |
| HC55185AIM | VoIP Ringing SLIC Family |
| HC55185DIM | VoIP Ringing SLIC Family |
| HC55181CIM | INDUCTOR 3.9NH +-.3NH 0402 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC55183 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Extended Reach Ringing SLIC Family |
| HC55183ECM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| HC55183ECMZ | 功能描述:電信線路管理 IC 75V RINGING SLIC W/BAT SWITCH POLV LB RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| HC55183ECMZ96 | 功能描述:電信線路管理 IC HC55183ECMEL RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| HC55184 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Extended Reach Ringing SLIC Family |
發布緊急采購，3分鐘左右您將得到回復。