參數資料
型號： HCS201
廠商： Microchip Technology Inc.
英文描述： KEELOQ Code Hopping Encoder
中文描述： 而Keeloq跳碼編碼器
文件頁數： 13/28頁
文件大?。?/td> 383K
代理商： HCS201
2001 Microchip Technology Inc.
DS41098C-page 13
HCS201
6.0
PROGRAMMING THE HCS201
When using the HCS201 in a system, the user will have
to program some parameters into the device including
the serial number and the secret key before it can be
used. The programming cycle allows the user to input
all 192 bits in a serial data stream, which are then
stored internally in EEPROM. Programming will be
initiated by forcing the DATA line high, after the S2 line
has been held high for the appropriate length of time
line (Table 6-1 and Figure 6-1). After the Program
mode is entered, a delay must be provided to the
device for the automatic bulk write cycle to complete.
This will write all locations in the EEPROM to an all
zeros pattern. The device can then be programmed by
clocking in 16 bits at a time, using S2 as the clock line
and DATA as the data in line. After each 16-bit word is
loaded, a programming delay is required for the internal
program cycle to complete. This delay can take up to
Twc. After every 16-bit word is written to the HCS201,
the HCS201 will signal that the write is complete by
sending out a train of ACK pulses, T
ACKH
high, T
ACKL
low (if the oscillator was perfectly tuned) on DATA.
These will continue until S2 is dropped. The first pulse’s
width should NOT be used for calibration. At the end of
the programming cycle, the device can be verified
(Figure 6-2) by reading back the EEPROM. Reading is
done by clocking the S2 line and reading the data bits
on DATA. For security reasons, it is not possible to exe-
cute a verify function without first programming the
EEPROM.
A Verify operation can only be done
once, immediately following the Program cycle
.
FIGURE 6-1:
PROGRAMMING WAVEFORMS
FIGURE 6-2:
VERIFY WAVEFORMS
Note:
To ensure that the device does not acci-
dentally enter Programming mode, DATA
should never be pulled high by the circuit
connected to it. Special care should be
taken when driving PNP RF transistors.
DATA
(Data)
Enter Program
Mode
(Clock)
Note 1:
S0 and S1 button inputs to be held to ground during the entire programming sequence.
Bit 0
Bit 1
Bit 2
Bit 3
Bit 14
Bit 15
Bit 16
Bit 17
T
PH
1
T
PBW
T
PS
Repeat for each word (12 times)
T
PH
2
T
CLKH
T
CLKL
T
WC
T
DS
S2
Data for Word 1
T
DH
T
CLKL
Initiate Data
Polling Here
Write Cycle
Complete Here
T
ACKL
T
ACKH
Calibration Pulses
T
PHOLD
Ack
Ack
Ack
DATA
(Data)
(Clock)
Note:
If a Verify operation is to be done, then it must immediately follow the Program cycle.
End of Programming Cycle
Beginning of Verify Cycle
Bit 1
Bit 2
Bit 3
Bit 15
Bit 14
Bit 16 Bit 17
Bit190 Bit191
T
WC
Data from Word 0
T
DV
S2
Bit 0
Bit191
Bit190
Ack
相關PDF資料
PDF描述
HCS20HMSR Radiation Hardened Dual 4-Input NAND Gate
HCS20D Radiation Hardened Dual 4-Input NAND Gate
HCS20DMSR Radiation Hardened Dual 4-Input NAND Gate
HCS20K Radiation Hardened Dual 4-Input NAND Gate
HCS20KMSR Radiation Hardened Dual 4-Input NAND Gate
相關代理商/技術參數
參數描述
HCS2-01 制造商:Richco 功能描述:HINGED CABLE SADDLE,NAT,16MM CBL
HCS201/P 功能描述:編碼器、解碼器、復用器和解復用器 3.5-13V RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HCS201/SN 功能描述:編碼器、解碼器、復用器和解復用器 3.5-13V RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HCS201_11 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:KEELOQ? Code Hopping Encoder 34-bit fixed code (28-bit serial number
HCS201-I/P 功能描述:編碼器、解碼器、復用器和解復用器 3.5-13V RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*