- 您現在的位置：買賣IC網 > PDF目錄371783 > HCS412IP (Microchip Technology Inc.) KEELOQ Code Hopping Encoder and Transponder PDF資料下載
參數資料
| 型號： | HCS412IP |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | KEELOQ Code Hopping Encoder and Transponder |
| 中文描述： | 而Keeloq跳碼編碼器和轉發器 |
| 文件頁數： | 18/44頁 |
| 文件大?。?/td> | 704K |
| 代理商： | HCS412IP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
HCS412
DS41099C-page 18
Preliminary
2002 Microchip Technology Inc.
4.0
TRANSPONDER OPERATION
4.1
IFF Mode
The HCS412
’s IFF Mode allows it to function as a bi-
directional token or transponder. IFF mode capabilities
include the following.
A bi-directional challenge and response sequence
for IFF validation. HCS412 IFF responses may be
directed to use one of two available encryption
algorithms and one of two available crypt keys.
Read selected EEPROM areas.
Write selected EEPROM areas.
Request a code hopping transmission.
Proximity Activation of a code hopping transmis-
sion.
4.2
IFF Communication
The transponder reader initiates each communication
by turning on the low frequency field, then waits for a
HCS412 to Acknowledge the field.
The HCS412 enters IFF mode upon detecting a signal
on the LC0 LF antenna input pin. Once the incoming
signal has remained high for at least the power-up time
T
PU
, the device responds with a field Acknowledge
sequence indicating that the it has detected the LF
field, is in IFF Mode and is ready to receive commands
(Figure 4-1). The HCS412 will repeat the field Acknowl-
edge sequence every 255 LF
TE
‘s if the field remains
but no command is received (Figure 4-1).
The transponder reader follows the HCS412’s field
Acknowledge by sending the desired 5-bit command
and associated data. LF commands are always pre-
ceded by a 2 LF
TE
low START pulse and are Pulse
Position Modulated (PPM) as shown in Figure 4-2. The
last command or data bit should be followed by leaving
the field on for a minimum of 6 LF
TE
.
HCS412 PPM data responses are preceded by a 1
LF
TE
low pulse, followed by a 01b preamble before the
data begins (Figure 4-4). The responses are sent either
on the LC antenna output alone or on both the LC out-
put and the DATA pin, depending on the device config-
uration (Section 4.4.2). This allows for short-range LF
responses as well as long-range RF responses.
Data to and from the HCS412 is always sent Least Sig-
nificant bit first. The data length and modulation format
vary according to the command and the transmission
path.
Data Length and Commands:
Read and Write transfers 16 bits of data.
Challenge and Response transfers 32 bits of data.
Modulation Format and Transmission Path:
LF responses on the LC output are Pulse Position
Modulated (PPM) according to Figure 4-2.
RF responses on the DATA pin modulate accord-
ing to standard encoder transmissions
(Figure 3-5, Figure 3-6).
Communication with the HCS412 over the low fre-
quency path (LC pins) uses a basic Timing Element,
LF
TE
. The Low Frequency Baud Rate Select option,
LFBSL, sets LF
TE
to either 100
μ
s or 200
μ
s
(Table 4-1).
The response on the DATA pin uses the Encoder
mode’s RF Timing Element (RF
TE
) and the modulation
format set by the MOD configuration option (Table 3-6).
The RF responses use the standard Encoder mode for-
mat with the 32-bit hopping portion replaced by the
response data (Figure 4-19). If the response is only 16
bits, the 32 bits will contain 2 copies of the response
(Figure 4-16).
TABLE 4-1:
LOW FREQUENCY BAUD
RATE SELECT BITS
4.2.1
CALCULATING COMMUNICATION TE
The HCS412’s internal oscillator will vary ±10% over
the device’s rated voltage and temperature range.
When the oscillator varies, both its transmitted T
E
and
expected T
E
when receiving will vary.
Communication reliability with the token may be
improved by calculating the HCS412’s T
E
from the field
Acknowledge sequence and using this measured time
element in communication to and in reception routines
from the token.
Always begin and end the time measurement on rising
edges. Whether LF or RF, the falling edge decay rates
may vary but the rising edge relationships should
remain consistent. A common T
E
calculation method
would be to time an 8 T
E
sequence, then divide the
value down to determine the single T
E
value. An 8 T
E
measurement will give good resolution and may be
easily right-shifted (divide by 2) three times for the math
portion of the calculation (Figure 4-1).
Accurately measuring T
E
is important for communicat-
ing to an HCS412 as well as for inductive programming
a device. The configuration word sent during program-
ming contains the 4-bit oscillator tuning value. Accu-
rately determining T
E
allows the programmer to
calculate the correct oscillator tuning bits to place in the
configuration word, whether the device oscillator needs
to be sped up or slowed down to meet its desired T
E
.
LFBSL
LF
TE
0
1
200
μ
s
100
μ
s
相關PDF資料 |
PDF描述 |
|---|---|
| HCS412TSN | KEELOQ Code Hopping Encoder and Transponder |
| HCS473 | Code Hopping Encoder and Transponder |
| HCS473-PQTP | Code Hopping Encoder and Transponder |
| HCS473-PROM | Code Hopping Encoder and Transponder |
| HCS473-PSQTP | IC EEPROM SRL 512X16BIT 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCS412P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:KEELOQ Code Hopping Encoder and Transponder |
| HCS412SN | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:KEELOQ Code Hopping Encoder and Transponder |
| HCS412T | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:KEELOQ Code Hopping Encoder and Transponder |
| HCS412T/SN | 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| HCS412TI | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:KEELOQ Code Hopping Encoder and Transponder |
發布緊急采購，3分鐘左右您將得到回復。