參數資料
型號: HCS473-SLROM
廠商: Microchip Technology Inc.
英文描述: Code Hopping Encoder and Transponder
中文描述: 跳碼編碼器和轉發器
文件頁數: 20/68頁
文件大小: 1629K
代理商: HCS473-SLROM
HCS473
DS40035C-page 18
Preliminary
2002 Microchip Technology Inc.
FIGURE 3-8:
LED OPERATION
3.1.6
CYCLE REDUNDANCY CHECK
(CRC)
The decoder can use the CRC bits to check the data
integrity before processing begins. The CRC is calcu-
lated on the previously transmitted bits (Figure 3-2),
detecting all single bit and 66% of all double bit errors.
EQUATION 3-1:
CRC CALCULATION
and
with
and Di
n
the nth transmission bit 0
n
64
3.1.7
COUNTER OVERFLOW BITS
(OVR1, OVR0)
The Counter Overflow Bits may be utilized to increase
the 16-bit synchronization counter range from the nom-
inal 65,535 to 131,070 or 196,605. The bits do not exist
when the device is configured for 20-bit counter opera-
tion.
The bits must be programmed during production as ‘1’s
to be utilized. OVR0 is cleared the first time the syn-
chronization counter wraps from FFFFh to 0000h.
OVR1 is cleared the second time the synchronization
counter wraps to zero. The two bits remain at ‘0’ after
all subsequent counter wraps.
3.1.8
DISCRIMINATION VALUE (DISC)
The Discrimination Value is typically used by the
decoder in a post-decryption check. It may be any
value, but in a typical system it will be programmed
equal to the Least Significant bits of the serial number.
The discrimination bits are part of the information that
form the encrypted portion of the transmission
(Figure 3-2). After the receiver has decrypted a trans-
mission, the discrimination bits are checked against the
receiver’s stored value to verify that the decryption pro-
cess was valid; appropriate decryption key was used. If
the discrimination value was programmed as the LSb’s
of the serial number then it may merely be compared to
the respective bits of the received serial number.
The discrimination bit field size varies with the counter
select (CNTSEL) option (Figure 3-2).
3.2
Transponder Mode
The HCS473’s Transponder mode allows it to function
as a bi-directional communication transponder. Com-
mands are received on the LC pins, responses may be
returned on either the LC pins or DATA pin for short
range LF or long range RF responses, respectively.
Transponder mode capabilities include:
A bi-directional challenge and response sequence
for IFF validation.
Read selected EEPROM areas.
Write selected EEPROM areas.
Request a code hopping transmission.
Proximity Activation of a code hopping transmis-
sion.
Address an individual transponder when multiple
units are within the LF field; device selection for
anticollision communication purposes.
SWITCH Sx
LED -
DATA
T
LEDON
T
LEDOFF
Code Word
Code Word
Code Word
T
LEDON
V
DD
>V
LOWSEL
(good battery)
LED -
V
DD
V
LOWSEL
(flat battery)
Note:
See Section 4.0, Programming Specs, for
information on programming OVR bits.
CRC 1
n
1
+
CRC 0
n
Di
n
=
CRC 0
n
1
+
CRC 0
n
Di
n
(
)
CRC 1
n
=
CRC 1 0
]
0
0
=
相關PDF資料
PDF描述
HCS473-SLSQTP Code Hopping Encoder and Transponder
HCS473IPQTP Code Hopping Encoder and Transponder
HCS473IPROM Code Hopping Encoder and Transponder
HCS473IPSQTP Code Hopping Encoder and Transponder
HCS473ISLQTP Code Hopping Encoder and Transponder
相關代理商/技術參數
參數描述
HCS473SLSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473-SLSQTP 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473T/SL 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HCS473T-I/SL 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量(輸入/輸出):2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HCS4870C 制造商:Power-One 功能描述:POWER SUPPLY