- 您現在的位置：買賣IC網 > PDF目錄370459 > HD404391S (Hitachi,Ltd.) 4-bit HMCS400-series microcomputer(4位單片微計算機) PDF資料下載
參數資料
| 型號： | HD404391S |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | 4-bit HMCS400-series microcomputer(4位單片微計算機) |
| 中文描述： | 4位HMCS400系列微電腦（4位單片微計算機） |
| 文件頁數： | 25/100頁 |
| 文件大?。?/td> | 610K |
| 代理商： | HD404391S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
HD404344R Series/HD404394 Series
25
Interrupts
There are five kinds of interrupts: external
INT
0
, timer B, timer C, serial interface, and A/D converter.
An interrupt request flag or an interrupt mask and vector address are used for each type of interrupt. They
are used for storing interrupt requests and interrupt controls. An interrupt enable flag is also used for total
interrupt control.
Interrupt Control Bits and Interrupt Processing:
The interrupt control bits are mapped from $000 to
$003 of RAM and can be accessed by RAM bit manipulation instructions. However, the interrupt request
flag (IF) cannot be set by software. An MCU reset initializes the interrupt enable flag (IE) and the interrupt
request flag (IF) to 0, and the interrupt mask (IM) to 1.
A block diagram of the interrupt control circuit is shown in figure 8. The interrupt priority order and vector
addresses are listed in a table in the figure, along with the conditions for executing the interrupt processing
of the five types of interrupt requests (table 2). An interrupt request occurs when the interrupt request flag
is set to 1 and the interrupt mask to 0. If the interrupt enable flag is 1, interrupt processing has occurred.
The vector address which corresponds to the interrupt source is generated from the priority PLA.
The interrupt processing sequence is shown in figure 9 and the interrupt processing flowchart is shown in
figure 10. After receiving an interrupt, the previous instruction is completed in the first cycle. The interrupt
enable flag (IE) is reset after two cycles. The contents of the carry flag, status flag, and program counter are
stored onto the stack at the second and third cycles. Instruction execution is restarted by jumping to the
vector address during the third cycle. The JMPL instructions, which branch to the start addresses of the
interrupt routines, should be programmed at each vector address area. The interrupt request which initiated
the interrupt processing should be reset by software instructions in the interrupt routine.
相關PDF資料 |
PDF描述 |
|---|---|
| HD404392S | 4-bit HMCS400-series microcomputer(4位單片微計算機) |
| HD404341R | 4-bit HMCS400-series microcomputer(4位單片微計算機) |
| HD404394S | 4-bit HMCS400-series microcomputer(4位單片微計算機) |
| HD404612 | 4-Bit Single-Chip Microcomputer |
| HD404612FS | 4-Bit Single-Chip Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD404392 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:HMCS43XXFamily User＇s Manual/Device |
| HD404392FP | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit microcomputers |
| HD404392FT | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit microcomputers |
| HD404392S | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit microcomputers |
| HD404394 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-bit microcomputer has an A/D converter |
發布緊急采購，3分鐘左右您將得到回復。