- 您現在的位置：買賣IC網 > PDF目錄370471 > HD66705U (Hitachi,Ltd.) Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver(圖形LCD控制器/驅動器) PDF資料下載
參數資料
| 型號： | HD66705U |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver(圖形LCD控制器/驅動器) |
| 中文描述： | 低功耗點陣液晶顯示控制器/驅動器（圖形液晶顯示控制器/驅動器） |
| 文件頁數： | 29/81頁 |
| 文件大小： | 426K |
| 代理商： | HD66705U |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
HD66705U
29
Power Control
The cursor control instruction (Figure 12) includes the AMP, SLP, and STB bits.
AMP:
When AMP = 1, each voltage-follower for V1 to V5 pins and the booster are turned on. When
AMP = 0, current consumption can be reduced while character or segment display controlled by the
multiplexing drive method is not being used.
SLP:
When SLP = 1, the
HD66705U
enters sleep mode, where all the internal operations are halted except
for annunciator display function and the R-C oscillator, thus reducing current consumption. Refer to the
Sleep Mode section. Only the following instructions can be executed during sleep mode.
a. Annunciator address set (AAN)
b. Annunciator data write
c. Annunciator display on or off (DA = 1 or 0)
d. Voltage-follower on or off (AMP = 1 or 0)
e. Standby mode set (STB = 1)
f.
Sleep mode cancel (SLP = 0)
During sleep mode, other RAM data and instructions cannot be updated but they are retained.
STB:
When STB = 1, the
HD66705U
enters standby mode, where the device completely stops, halting all the
internal operations including the internal R-C oscillator and no external clock pulses are supplied.
However, annunciator display alone is available when the alternating signal for annunciator-driving signals
is supplied to the EXM pin. When the annunciator display is not needed, make sure to turn off display (DA
= 0). Refer to the Standby Mode section. Only the following instructions can be executed during standby
mode.
a. Annunciator address set (AAN)
b. Annunciator data write
c. Annunciator display on or off (DA = 1 or 0)
d. Voltage-follower on or off (AMP = 1 or 0)
e. Start oscillator
f.
Standby mode cancel (STB = 0)
During standby mode, RAM data and other instructions may be lost; they must be set again after standby
mode is cancelled.
0
0
0
0
0
1
1 AMPSLP
STB
RS R/W DB7
DB0
Figure 12 Power Control Instruction
相關PDF資料 |
PDF描述 |
|---|---|
| HD66710 | (Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66710A00FS | 16 AMP SPDT MINIATURE POWER RELAY |
| HD66710A00TF | (Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66712U | Dot-Matrix Liquid Crystal Display Controller/Driver(點陣液晶顯示控制器/驅動器) |
| HD66712 | Dot-Matrix Liquid Crystal Display Controller/Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD66710 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:(Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66710A00FS | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:(Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66710A00TF | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:(Dot Matrix Liquid Crystal Display Controller/Driver) |
| HD66712 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot-Matrix Liquid Crystal Display Controller/Driver |
| HD66712A00TA0 | 制造商:Renesas Electronics Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。