- 您現在的位置：買賣IC網 > PDF目錄371798 > HDSP-253 Eight Character 5 mm Smart Alphanumeric Display PDF資料下載
參數資料
| 型號： | HDSP-253 |
| 英文描述： | Eight Character 5 mm Smart Alphanumeric Display |
| 中文描述： | 八字5毫米智能字符顯示 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 201K |
| 代理商： | HDSP-253 |
15
Table 3. Maximum Allowable Ambient Temperature for Various Operating Conditions (cont’d.)
All Colors Except AlGaAs Red
Number of
Characters
Brightness
Level
V
DD
V
I
DD
mA
P
D
W
R
θ
J-A
°
C/W
39
39
39
T
A
MAX
°
C
72
77
85
Character
# (20 dots)
# (20 dots)
# (20 dots)
8
8
8
100%
100%
100%
5.5
5.25
5.0
373
354
335
2.0
1.9
1.67
# (20 dots)
# (20 dots)
# (20 dots)
7
6
8
100%
100%
80%
5.5
5.5
5.5
326
280
298
1.8
1.5
1.6
39
39
39
80
85
85
V (12 dots)
8
100%
5.5
207
1.1
39
85
The actual IC temperature is easy to measure. Pin 17 is thermally and electrically connected to the IC
substrate. The thermal resistance from pin 17 to the IC is 16
°
C/W. The procedure to measure the IC junction
temperature is as follows:
1. Measure V
DD
and I
DD
for the display. Measure V
DD
between pins 15 and 16. Measure the current entering
pin 15.
2. Measure the temperature of pin 17 after 45 minutes. Use an electrically isolated thermal couple probe.
3. T
J
(IC) = T
pin
+ V
DD
x I
DD
x 16
°
C/W.
Ground Connections
Two ground pins are provided to
keep the internal IC logic ground
clean. The designer can, when
necessary, route the analog
ground for the LED drivers
separately from the logic ground
until an appropriate ground plane
is available. On long inter-
connections between the display
and the host system, the designer
can keep voltage drops on the
analog ground from affecting the
display logic levels by isolating
the two grounds.
The logic ground should be con-
nected to the same ground poten-
tial as the logic interface circuitry.
The analog ground and the logic
ground should be connected at a
common ground which can
withstand the current induced by
the switching LED drivers.
When separate ground
connections are used, the analog
ground can vary from -0.3 V to
+0.3 V with respect to the logic
ground. Voltage below -0.3 V can
cause all dots to be on. Voltage
above +0.3 V can cause dimming
and dot mismatch.
Solder and Post Solder
Cleaning
Note: Freon vapors can cause the
black paint to peel off the display.
See Application Note 1027 for
information on soldering and post
solder cleaning.
Contrast Enhancement
(Filtering)
See Application Note 1015 for
information on contrast
enhancement.
相關PDF資料 |
PDF描述 |
|---|---|
| HDSP-3906 | 20 mm (0.8 inch) Seven Segment Displays |
| HDSP-8601 | 20 mm (0.8 inch) Seven Segment Displays |
| HDSP-8603 | 20 mm (0.8 inch) Seven Segment Displays |
| HDSP-8605 | Replaced by SN75ALS174A : Quadruple Differential Line Drivers 20-SOIC |
| HDSP-8606 | Replaced by SN75ALS174A : Quadruple Differential Line Drivers 16-PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HDSP-2530 | 功能描述:LED 顯示器和配件 Orange 602nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP-2531 | 功能描述:LED 顯示器和配件 Yellow 585nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP-2532 | 功能描述:LED 顯示器和配件 Red 626nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP-2533 | 功能描述:LED 顯示器和配件 Green 574nm 5x7 Smart Display RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| HDSP2533 | 制造商:Avago Technologies 功能描述:LED DISPLAY ALPHANUMERIC |
發布緊急采購，3分鐘左右您將得到回復。