參數資料
型號： HEDG-512X
英文描述： Two and Three Channel Codewheels for Use with Agilent Optical Encoder Modules
中文描述： 兩個和三個頻道Codewheels與安捷倫的光學編碼器模塊的使用
文件頁數： 5/14頁
文件大小： 227K
代理商： HEDG-512X
5
Figure 2. Alignment Tool is Used to Set Height of
Codewheel.
Assembly Instructions Using
Agilent Assembly Tools
Instructions
1. Place codewheel on shaft.
2. Set codewheel height:
(a) Place the correct gap
setting tool (per Ordering
Information Table) on motor
base, flush up against the
motor shaft as shown in Figure
2. The shim has two different
size steps. Choose the one that
most closely matches the width
of the codewheel boss. The
Figure 3. Alignment Tool is Placed over Shaft and onto
Codewheel Hub. Alignment Tool Pins Mate with
Aligning Recesses on Module.
CENTERING TOOL
CODEWHEEL
ALIGNING RECESSES
MODULE SIDE A
MODULE SIDE B
IMAGE SIDE OF CODEWHEEL
GAP SETTING SHIM
CODEWHEEL
MODULE SIDE A
MODULE SIDE B
shim should not contact the
codewheel boss.
(b) Push codewheel down
against gap setting shim. The
codewheel is now at the proper
height.
(c) Tighten codewheel
setscrew.
3. Insert mounting screws
through module and thread
into the motor base. Do not
tighten screws.
4. Slide the HEDS-8905 or HEDS-
8906 centering tool over
codewheel hub and onto
module as shown in Figure 3.
The pins of the alignment tool
should fit snugly inside the
alignment recesses of the
module.
5. While holding alignment tool in
place, tighten screws down to
secure module.
6. Remove alignment tools.
相關PDF資料
PDF描述
HEDG-612X Two and Three Channel Codewheels for Use with Agilent Optical Encoder Modules
HEDS-612X Two and Three Channel Codewheels for Use with Agilent Optical Encoder Modules
HEDS-61XX Two and Three Channel Codewheels for Use with Agilent Optical Encoder Modules
HEDL-560X Encoder Line Drivers(編碼器線驅動器)
HEDL-9040 Encoder Line Drivers(編碼器線驅動器)
相關代理商/技術參數
參數描述
HEDG-6120#U12 功能描述:編碼器 2 Channel 2048 CPR 6mm Code Wheel RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C
HEDG-6120-U12 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Two and Three Channel Codewheels for Use with Agilent Optical Encoder Modules
HEDG-612X 制造商:AGILENT 制造商全稱:AGILENT 功能描述:Two and Three Channel Codewheels for Use with Agilent Optical Encoder Modules
HEDG-9000-H13 功能描述:編碼器 17 Bit 2048 CPR 8mm Code Wheel RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C
HEDG-9000-H14 功能描述:編碼器 17 Bit 2048 CPR 13mm Code Wheel RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*