- 您現在的位置：買賣IC網 > PDF目錄370566 > HEDS-5645-S06 Quick Assembly Two and Three Channel Optical Encoders PDF資料下載
參數資料
| 型號： | HEDS-5645-S06 |
| 英文描述： | Quick Assembly Two and Three Channel Optical Encoders |
| 中文描述： | 快速大會二及中三通道光學編碼器 |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 288K |
| 代理商： | HEDS-5645-S06 |
10
3a. Push the hex wrench into the body of the encoder to
ensure that it is properly seated into the code wheel hub set
screws. Then apply a downward force on the end of the hex
wrench. This sets the code wheel gap by levering the code
wheel hub to its upper position.
3b. While continuing to apply a downward force, rotate the
hex wrench in the clockwise direction until the hub set
screw is tight against the motor shaft. The hub set screw
attaches the code wheel to the motor's shaft.
3c. Remove the hex wrench by pulling it straight out of the
encoder body.
4. Use the center screwdriver slot, or either of the two side
slots, to rotate the encoder cap dot clockwise from the one
dot position to the two dot position. Do not rotate the
encoder cap counterclockwise beyond the one dot position.
The encoder is ready for use!
Encoder Mounting and Assembly
1. For HEDS-5500 and 5600: Mount encoder base plate onto
motor. Tighten screws. Go on to step 2.
1a. For HEDS-5540, 5640 and HEDM-5500, 5600: Slip
alignment tool onto motor shaft. With alignment tool in
place, mount encoder baseplate onto motor as shown above.
Tighten screws. Remove alignment tool.
2. Snap encoder body onto base plate locking all 4 snaps.
相關PDF資料 |
PDF描述 |
|---|---|
| HEDS-5645-S11 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDS-5645-S12 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDS-5645-S13 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDS-5645-S14 | Quick Assembly Two and Three Channel Optical Encoders |
| HEDS-5640-C03 | Quick Assembly Two and Three Channel Optical Encoders |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HEDS5700 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:QUADRANT/CIRCULAR DETECTOR |
| HEDS-5700#A01 | 功能描述:編碼器 2 Channel 500CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-5700#A02 | 功能描述:編碼器 2 Channel 500CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-5700#A10 | 功能描述:編碼器 2 Channel 500CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| HEDS-5700#C01 | 功能描述:編碼器 2 Channel 100CPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
發布緊急采購，3分鐘左右您將得到回復。