參數資料
型號: HFA3863IN96
廠商: INTERSIL CORP
元件分類: 無繩電話/電話
英文描述: Direct Sequence Spread Spectrum Baseband Processor
中文描述: TELECOM, CELLULAR, BASEBAND CIRCUIT, PQFP64
封裝: 10 X 10 MM, PLASTIC, MS-026ACD, TQFP-64
文件頁數: 7/39頁
文件大小: 305K
代理商: HFA3863IN96
4-7
RXCLK is an output from the HFA3863 and is the clock for
the serial demodulated data on RXD. MD_RDY is an output
from the HFA3863 and it may be set to go active after the
SFD or CRC fields. Note that RXCLK becomes active after
the Start Frame Delimiter (SFD) to clock out the Signal,
Service, and Length fields, then goes inactive during the
header CRC field. RXCLK becomes active again for the
data. MD_RDY returns to its inactive state after RX_PE is
deactivated by the external controller, or if a header error is
detected. A header error is either a failure of the CRC
check, or the failure of the received signal field to match
one of the 4 programmed signal fields. For either type of
header error, the HFA3863 will reset itself after reception of
the CRC field. If MD_RDY had been set to go active after
CRC, it will remain low.
MD_RDY and RXCLK can be configured through CR 1, bits
1 and 0 to be active low, or active high. The receive port is
completely independent from the operation of the other
interface ports including the TX port, supporting therefore a
full duplex mode.
RX I/Q A/D Interface
The PRISM baseband processor chip (HFA3863) includes
two 6-bit Analog to Digital converters (A/Ds) that sample the
balanced differential analog input from the IF down converter
device (HFA3783). The I/Q A/D clock, samples at twice the
chip rate with a nominal sampling rate of 22MHz.
The interface specifications for the I and Q A/Ds are listed in
Table 1. The HFA3863 is designed to be DC coupled to the
HFA3783.
The voltages applied to pin 16, V
REF
and pin 21, I
REF
set
the references for the internal I and Q A/D converters. In
addition, For a nominal I/Q input of 400mV
P-P
, the
suggested V
REF
voltage is 1.2V.
AGC Circuit
The AGC circuit is designed to adjust for signal level
variations and optimize A/D performance for the I and Q
inputs by maintaining the proper headroom on the 6-bit
converters. There are two gain stages being controlled. At
RF, the gain control is a 30dB step change. This RF gain
control optimizes the receiver dynamic range when the
signal level is high and maintains the noise figure of the
receiver when it is needed most at low signal level. At IF the
gain control is linear and covers the bulk of the gain control
range of the receiver.
The AGC loop is partially digital which allows for holding the
gain fixed during a packet. The AGC sensing mechanism
uses a combination of the I and Q A/D converters and the
detected signal level in the IF to determine the gain settings.
The A/D outputs are monitored in the HFA3863 for the
desired nominal level. When it is reached, by adjusting the
receiver gain, the gain control is locked for the remainder of
the packet.
RX_AGC_IN Interface
The signal level in the IF stage is monitored to determine
when to impose the 30dB gain reduction in the RF stage.
This maximizes the dynamic range of the receiver by
keeping the RF stages out of saturation at high signal levels.
When the IF circuits’ sensor output reaches 0.5V
DD
, the
HFA3863 comparator switches in the 30dB pad and also
adds 30dB of gain to the IF AGC amplifier. This
compensates the IF AGC and RSSI measures.
TX I/Q DAC Interface
The transmit section outputs balanced differential analog
signals from the transmit DACs to the HFA3783. These are
DC coupled and digitally filtered.
Test Port
The HFA3863 provides the capability to access a number of
internal signals and/or data through the Test port, pins TEST
7:0. The test port is programmable through configuration
register (CR 34). Any signal on the test port can also be read
from configuration register (CR50) via the serial control port.
Additionally, the transmit DACs can be configured to show
signals in the receiver via CR 14. This allows visibility to
analog like signals that would normally be very difficult to
capture.
TABLE 1. I, Q, A/D SPECIFICATIONS
PARAMETER
MIN
TYP
MAX
Full Scale Input Voltage (V
P-P
)
0.90
1.00
1.10
Input Bandwidth (-0.5dB)
-
11MHz
-
Input Capacitance (pF)
-
2
-
Input Impedance (DC)
5k
-
-
f
S
(Sampling Frequency)
-
22MHz
-
HFA3863
相關PDF資料
PDF描述
HFA3863 Direct Sequence Spread Spectrum Baseband Processor(直接序列擴譜基帶處理器)
HFA3983IV96 2.4GHz Power Amplifier and Detector
HFA3983 2.4GHz Power Amplifier and Detector(2.4GHz 功率放大器探測器)
HFA3983IV 2.4GHz Power Amplifier and Detector
HFB60HF20 200V 60A Hi-Rel Ultra-Fast Discrete Diode in a SMD-1 package
相關代理商/技術參數
參數描述
HFA3925 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:null2.4GHz - 2.5GHz 250mW Power Amplifier
HFA3925IA 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述:
HFA3925IA1K 制造商:Rochester Electronics LLC 功能描述:- Bulk
HFA3925IA96 制造商:Rochester Electronics LLC 功能描述:- Bulk
HFA3926 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:2.0GHz - 2.7GHz 250mW Power Amplifier