- 您現在的位置：買賣IC網 > PDF目錄371814 > HI5628 (Intersil Corporation) 8-Bit, 165/125/60MSPS, Dual High Speed CMOS D/A Converter PDF資料下載
參數資料
| 型號： | HI5628 |
| 廠商： | Intersil Corporation |
| 英文描述： | 8-Bit, 165/125/60MSPS, Dual High Speed CMOS D/A Converter |
| 中文描述： | 8位，165/125/60MSPS，雙路高速CMOS D / A轉換 |
| 文件頁數： | 9/10頁 |
| 文件大?。?/td> | 93K |
| 代理商： | HI5628 |
9
Noise Reduction
To minimize power supply noise, 0.1
μ
F capacitors should be
placed as close as possible to the converter’s power supply
pins, AV
DD
and DV
DD
. Also, should the layout be designed
using separate digital and analog ground planes, these
capacitors should be terminated to the digital ground for
DV
DD
and to the analog ground for AV
DD
. Additional filtering
of the power supplies on the board is recommended.
Voltage Reference
The internal voltage reference of the device has a nominal
value of +1.2V with a
±
60 ppm/
o
C drift coefficient over the full
temperature range of the converter. It is recommended that a
0.1
μ
F capacitor be placed as close as possible to the REFIO
pin, connected to the analog ground. The REFLO pin (15)
selects the reference. The internal reference can be selected if
pin 15 is tied low (ground). If an external reference is desired,
then pin 15 should be tied high (to the analog supply voltage)
and the external reference driven into REFIO, pin 23. The full
scale output current of the converter is a function of the voltage
reference used and the value of R
SET
. I
OUT
should be within
the 2mA to 20mA range, through operation below 2mA is
possible, with performance degradation.
If the internal reference is used, V
FSADJ
will equal
approximately 1.16V (pin 22). If an external reference is used,
V
FSADJ
will equal the external reference. The calculation for
I
OUT
(Full Scale) is:
I
OUT
(Full Scale) = (V
FSADJ
/R
SET
)x 32.
If the full scale output current is set to 20mA by using the
internal voltage reference (1.16V) and a 1.86k
R
SET
resistor, then the input coding to output current will resemble
the following:
Outputs
IOUTA and IOUTB (or QOUTA and QOUTB) are
complementary current outputs. The sum of the two currents
is always equal to the full scale output current minus one
LSB. If single ended use is desired, a load resistor can be
used to convert the output current to a voltage. It is
recommended that the unused output be either grounded or
equally terminated. The voltage developed at the output
must not violate the output voltage compliance range of
-0.3V to 1.25V. R
LOAD
should be chosen so that the desired
output voltage is produced in conjunction with the output full
scale current, which is described above in the ‘Reference’
section. If a known line impedance is to be driven, then the
output load resistor should be chosen to match this
impedance. The output voltage equation is:
V
OUT
= I
OUT
X R
LOAD
.
These outputs can be used in a differential-to-single-ended
arrangement to achieve better harmonic rejection. The
SFDR measurements in this data sheet were performed with
a 1:1 transformer on the output of the DAC (see Figure 1).
With the center tap grounded, the output swing of pins 16
and 17 will be biased at zero volts. It is important to note
here that the negative voltage output compliance range limit
is -300mV, imposing a maximum of 600mV
P-P
amplitude
with this configuration. The loading as shown in Figure 1 will
result in a 500mV signal at the output of the transformer if
the full scale output current of the DAC is set to 20mA.
V
OUT
= 2 x I
OUT
x R
EQ ,
where R
EQ
is ~12.5
.
Allowing the center tap to float will result in identical
transformer output, however the output pins of the DAC will
have positive DC offset. The 50
load on the output of the
transformer represents the spectrum analyzer’s input
impedance.
TABLE 1. INPUT CODING vs OUTPUT CURRENT
INPUT CODE (D7-D0)
IOUTA (mA)
IOUTB (mA)
111 11111
20
0
100 00000
10
10
000 00000
0
20
PIN 17 (20)
PIN 16 (21)
V
OUT
= (2 x I
OUT
x R
EQ
)V
100
50
50
50
IOUTB (QOUTB)
IOUTA (QOUTA)
FIGURE 4.
HI5628
相關PDF資料 |
PDF描述 |
|---|---|
| HI5628IN | Power Resistor; Series:200; Resistance:1ohm; Resistance Tolerance:+/- 5%; Power Rating:8W; Resistor Element Material:Ceramic; Temperature Coefficient:+/-400 ppm; Leaded Process Compatible:Yes; Packaging:Bulk RoHS Compliant: Yes |
| HI5630 | Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5630CN | Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5630EVAL | Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5634 | High Performance Programmable Phase-Locked Loop for LCD Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5628/16IN | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:8-Bit, 165/125/60MSPS, Dual High Speed CMOS D/A Converter |
| HI5628/6IN | 功能描述:DAC DUAL 8BIT 60MSPS 48LQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| HI5628/6IN-T | 功能描述:DAC DUAL 8BIT 60MSPS 48LQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| HI5628/6INZ | 功能描述:數模轉換器- DAC D/A DL 8-BIT 60MSPS LQFP IND TEMPHI5728I RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| HI5628/IN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter |
發布緊急采購，3分鐘左右您將得到回復。