參數資料
| 型號： | HI7190IBZ-T |
| 廠商： | Intersil |
| 文件頁數： | 10/25頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT PROGBL SER 20-SOIC |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 位數： | 24 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 32.5mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC W |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
18
FN3612.10
June 27, 2006
Instruction Register
The Instruction Register is an 8-bit register which is used
during a communications cycle for setting up read/write
operations.
R/W - Bit 7 of the Instruction Register determines whether a
read or write operation will be done following the instruction
byte load. 0 = READ, 1 = WRITE.
MB1, MB0 - Bits 6 and 5 of the Instruction Register
determine the number of bytes that will be accessed
following the instruction byte load. See Table 5 for the
number of bytes to transfer in the transfer cycle.
FSC - Bit 4 is used to determine whether a Positive Full Scale
Calibration Register I/O transfer (FSC = 0) or a Negative Full
Scale Calibration Register I/O transfer (FSC = 1) is being
performed (see Table 6).
A3, A2, A1, A0 - Bits 3 and 2 (A3 and A2) of the Instruction
Register determine which internal register will be accessed
while bits 1 and 0 (A1 and A0) determine which byte of that
register will be accessed first. See Table 6 for the address
decode.
Write Operation
Data can be written to the Control Register, Offset
Calibration Register, Positive Full Scale Calibration Register,
and the Negative Full Scale Calibration Register. Write
operations are done using the SDIO, CS and SCLK lines
only, as all data is written into the HI7190 via the SDIO line
show typical write timing diagrams.
The communication cycle is started by asserting the CS line
low and starting the clock from its idle state. To assert a write
cycle, during the instruction phase of the communication
cycle, the Instruction Byte should be set to a write transfer
(R/W = 1).
When writing to the serial port, data is latched into the
HI7190 on the rising edge of SCLK. Data can then be
changed on the falling edge of SCLK. Data can also be
changed on the rising edge of SCLK due to the 0ns hold time
required on the data. This is useful in pipelined applications
where the data is latched on the rising edge of the clock.
Read Operation - 3-Wire Transfer
Data can be read from the Data Output Register, Control
Register, Offset Calibration Register, Positive Full Scale
Calibration Register, and the Negative Full Scale Calibration
Register. When configured in 3-wire transfer mode, read
operations are done using the SDIO, SDO, CS and SCLK
show typical 3-wire read timing diagrams.
The communication cycle is started by asserting the CS line
and starting the clock from its idle state. To assert a read
cycle, during the instruction phase of the communication
cycle, the Instruction Byte should be set to a read transfer
(R/W = 0).
When reading the serial port, data is driven out of the HI7190
on the falling edge of SCLK. Data can be registered
externally on the next rising edge of SCLK.
Read Operation - 2-Wire Transfer
Data can be read from the Data Output Register, Control
Register, Offset Calibration Register, Positive Full Scale
Calibration Register, and the Negative Full Scale Calibration
Register. When configured in two-wire transfer mode, read
operations are done using the SDIO, CS and SCLK lines. All
typical 2-wire read timing diagrams.
INSTRUCTION REGISTER
MSB
654321
LSB
R/W
MB1
MB0
FSC
A3
A2
A1
A0
TABLE 5. MULTIPLE BYTE ACCESS BITS
MB1
MB0
DESCRIPTION
0
Transfer 1 Byte
0
1
Transfer 2 Bytes
1
0
Transfer 3 Bytes
1
Transfer 4 Bytes
TABLE 6. INTERNAL DATA ACCESS DECODE STARTING
BYTE
FSC A3A2A1A0
DESCRIPTION
X
0000
Data Output Register, Byte 0
X
0001
Data Output Register, Byte 1
X
0010
Data Output Register, Byte 2
X
0100
Control Register, Byte 0
X
0101
Control Register, Byte 1
X
0110
Control Register, Byte 2
X
1000
Offset Cal Register, Byte 0
X
1001
Offset Cal Register, Byte 1
X
1010
Offset Cal Register, Byte 2
0
1100
Positive Full Scale Cal Register, Byte 0
0
1101
Positive Full Scale Cal Register, Byte 1
0
1110
Positive Full Scale Cal Register, Byte 2
1
1100
Negative Full Scale Cal Register, Byte 0
1
1101
Negative Full Scale Cal Register, Byte 1
1
1110
Negative Full Scale Cal Register, Byte 2
TABLE 6. INTERNAL DATA ACCESS DECODE STARTING
BYTE (Continued)
FSC A3A2A1A0
DESCRIPTION
HI7190
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B1P-MW-F4 | CONVERTER MOD DC/DC 13.8V 100W |
| GTC030-28-1P | CONN RCPT 9POS PANEL MNT W/PINS |
| VI-B1P-MW-F3 | CONVERTER MOD DC/DC 13.8V 100W |
| MS27508E20F35PA | CONN RCPT 79POS BOX MNT W/PINS |
| ICS1893BFLF | PHYCEIVER LOW PWR 3.3V 48-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI7190IP | 功能描述:IC ADC 24BIT PROGBL SER 20-PDIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| HI7190IPZ | 功能描述:模數轉換器 - ADC W/ANNEAL ADC 24BIT 1 0HZ SIGMADELTA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| HI7191 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:24-Bit, High Precision, Sigma Delta A/D Converter |
| HI7191_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:24-Bit, High Precision, Sigma Delta A/D Converter |
| HI7191IB | 功能描述:IC ADC 24BIT PROGBL SER 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
發布緊急采購，3分鐘左右您將得到回復。